Altec Lansing XT1 User Manual (English)

Questions and Answers:

K
Kaitlyn MooreJul 30, 2025
What to do if there is no sound from one or both Altec Lansing XT1 Stereo System speakers?
- F
  flesterJul 30, 2025
  If you're not getting sound from one or both speakers, try these steps: * Ensure the speaker stand cable is properly connected to both speakers. * Increase the volume by pushing the “+” button. * Check the volume level on the computer operating system or other audio source and set it at a mid-level. * If using the auxiliary input, check that the 3.5 mm stereo cable is firmly connected to the correct jacks on the audio source. * Make sure the 3.5 mm stereo cable is connected to the “line-out,” “audio-out,” or the headphone jack of the audio source. * Test the speakers on another audio device to rule out a problem with the original audio source.
J
James PettyAug 3, 2025
Why are no LEDs lit on my Altec Lansing XT1?
- C
  Caitlin SawyerAug 3, 2025
  If no LEDs are lit, it could be due to a few reasons: * The power isn’t turned on. Turn on the speaker system by pushing the power button on the right satellite. An LED will light on the front of the right satellite when the power is ON. * The speaker system is not connected to a laptop computer or PC via the USB port. Connect the speaker system to a laptop computer or PC via the USB port. * The laptop computer or PC is in sleep mode. Make sure the computer is active.
P
Patricia MillerAug 7, 2025
How to fix distorted sound on Altec Lansing Stereo System?
- S
  Sandra IngramAug 7, 2025
  Sound distortion can occur for several reasons. Try the following: * Decrease the volume by pushing the “–” button. * Adjust the computer operating system volume and balance levels to the center as a starting point, then adjust the level on the speaker using the volume control. * If the audio source is distorted, try a different audio source such as a music CD. WAV files are often of poor quality. * Adjust audio source EQ levels to “flat.”
P
Paul WuAug 12, 2025
What causes crackling sound from Altec Lansing XT1 speakers?
- D
  david76Aug 12, 2025
  Crackling sounds can be caused by a volume level in computer operating system that is set too high. Check the computer operating system volume level and decrease it if necessary. Another cause can be a problem with your audio source device. Unplug the 3.5 mm stereo cable from the audio source. Then plug it into the headphone jack of an alternate audio source (e.g., Walkman, Discman or FM radio).
T
tiffany69Aug 16, 2025
What to do if volume output cannot be controlled by the computer operating system’s CD level controls on Altec Lansing XT1 Stereo System?
- S
  Shannon GravesAug 16, 2025
  Control master volume by using the “+” and “–” volume buttons on the right satellite speaker or the master and wave level controls on the computer’s operating system.
N
Nicholas ParkerAug 20, 2025
What causes broken audio from Altec Lansing Stereo System speakers?
- G
  gclarkAug 20, 2025
  If you are experiencing broken audio, it could be due to: * Speakers are connected to a computer running Windows 98SE. Broken audio issue should resolve itself once Windows 98SE has finished the loading cycle. * The computer is running too many applications at the same time. Quit one or more applications until the problem is resolved or increase computer memory (RAM) or storage space.
J
jennifer11Aug 25, 2025
How to stop radio interference on Altec Lansing Stereo System?
- S
  Sarah OrozcoAug 26, 2025
  Radio interference can occur if the speakers are too close to a radio tower. Move your speakers until the interference goes away.