Altronics FOTEK NT-RV Series - User Manual

■ Specification / Especificaciones:
Type
DIN 48*48
DIN 72*72 /48*96 /96*96
DIN 24*48
Model
NT-48RV-AF
NT-XX-RV-AF
NT-10-AF
Output method
Relay & SSR
Relay or SSR
Rated current
Relay （5A/250VAC）；SSR（30mA/12V）
Operating voltage
90~265VAC 50/60Hz
Alarm output
Relay （5A/250VAC）
Control method
PID + Fuzzy
Input method
PT / K / J / R / S / T/ B / E / N / L Selectable
Display range
-999 ~ 9999 或 -99.9 ~ 999.9 Selectable
Accuracy of display
± ( 0.1 % of F.S. + 1 DIGIT)
Setting range
-999 ~ 9999 或 -99.9 ~ 999.9 Selectable
Dielectric strength
Over 2.5KV
Isolation strength
Over 100MΩ / 500VDC
Operating temp
﹣20℃ ~ ﹢80℃；35 ~ 85％RH
Housing material
Intensive PC+ABS（UL-94V0）
■ Mode of alarm / Modos de Alarma
ALt
Description / Descripción
ALt
Description / Descripción
ALt
Description / Descripción
0
AL1 ON
SV (SV+AL1)
AL2 ON
SV (SV+AL2)
1
AL1 ON
(SV - AL1) SV
AL2 ON
SV (SV+AL2)
2
AL1 ON
(SV - AL1) SV
AL2 ON
(SV – AL2) SV
3
AL1 ON
(SV – AL2) SV (SV+AL1)
AL2 ON
SV (SV+AL2)
4
AL1 ON
(SV – AL1) SV (SV+AL1)
AL2 ON
SV （SV+AL2）
5
AL1 ON
(SV - AL1) SV (SV+AL1)
AL2 ON
SV (SV+AL2)
6
AL1 ON
AL1
AL2 ON
AL2
7
AL1 ON First cycle unable
AL1
AL2 ON
AL2
8
AL1 ON First cycle unable
(SV - AL1) SV
AL2 ON
SV (SV+AL2)
9
AL1 ON First cycle unable
(SV - AL1) SV (SV+AL1)
AL2 ON
SV (SV+AL2)
10
AL1 ON
SV (SV+AL1)
AL2 ON
SV tnr 99h59m
11
AL1 ON
AL1
AL2 ON
AL2
12
AL1 ON
AL1
AL2 ON
AL2
13
AL1 ON
SV (SV+AL1)
AL2 ON
(SV – AL2) SV
14
AL1 ON
SV (SV+AL1)
AL2 ON
(SV – AL2) SV
15
AL1 ON 1 Flicker
SV (SV+AL1)
AL2 ON
SV (SV+AL2)
16
AL1 ON
SV (SV+AL1)
AL2 ON
SV tnr 99h59m
17
AL1 ON
SV (SV+AL1)
AL2 ON
SV tnr 99m59s
18
AL1 ON
SV (SV+AL1)
AL2 ON
SV tnr 99m59s
19
Non-used
20
AL1 ON 1 Flicker
SV (SV+AL1)
AL2 ON
SV (SV+AL2)
21
AL1 ON 1 Flicker
SV (SV+AL1)
AL2 ON First cycle unable
(SV - AL1) SV (SV+AL2)
22
AL1 ON 1 Flicker
SV (SV+AL1)
AL2 ON
(SV - AL1) SV
23
AL1 ON 1 Flicker
SV (SV+AL1)
AL2 ON
(SV - AL1) SV
24
AL1 ON 1 Flicker
SV (SV+AL1)
AL2 ON
(SV - AL1) SV (SV+AL2)
25
AL1 ON 1 Flicker
SV (SV+AL1)
AL2 ON
(SV - AL1) SV (SV+AL2)
26
AL1 ON
AL1 SV
AL2 ON First cycle unable
(SV – AL2) SV
1.「ALt=15」： t = ON time of AL2 for cooling, OFF time is controlled by PID.
2.「ALH」：Hysteresis of alarm. Ex. PV≧(SV+AL1)→AL1 ON, PV＜(SV+AL1-ALH)→AL1 OFF
3.「tnu」= Process time of tnr, if「tnu≧tnr」→ AL2 is turned ON or OFF
UL CE
RoHs
Instruction Manual / Manual de Uso
F - 71
NT-XX-RV-AF series All function temperature controller
Thank you very much for using FOTEK NT-XX-RV series All function Temperature controller
Please read this instruction manual before operating it to avoid from the malfunction.
FOTEK NT10-R-AF / NT-22-R-AF / NT-48RV / NT-72-RV / NT-20-RV / NT-21-RV / NT96-RV-AF
AlltronicsPerú
AUTOMATIZACIÓN INDUSTRIAL
https://www.fotek.com.tw
https://alltronicsperu.com

Summary

Specification and Specifications

Model Specifications

Details on model types, output methods, current, voltage, and operating parameters.

Alarm Modes and Descriptions

Defines various alarm modes (AL1, AL2) and their operational descriptions.

Operating Procedures

Setting Heating Timer

Instructions for setting the heating timer, including its completion behavior.

Selecting Display Mode

Procedure to switch between temperature setting and heating time display.

Soft Start Configuration

Details on configuring and using the soft start feature for gradual ramp-up.

Manual Control Mode

How to enter and operate the manual control mode for the device.

OFF (Stop) Function

Steps to place the controller into or release it from the stop control status.

Auto-Tuning (AT) Function

Initiating and exiting the auto-tuning process for optimal performance.

Parameter Setting

Instructions to access and modify device parameters.

Alarm Setting Configuration

Procedure for configuring alarm settings and thresholds.

Alarm Parameter Settings

Lock Setting Configuration

Configure the lock status to control parameter settability.

AL1 Limit Setting

Set the limit value for the AL1 alarm.

Alarm Hysteresis Setting

Define the hysteresis range for alarm activation and deactivation.

Alarm Delay Time

Set the delay time before an alarm condition is triggered.

Setting Limit Configuration

Configure the maximum limit for settings.

Output Limit Setting

Limit the range of the output volume.

Process Output Volume Display

Display the current process output volume.

Minimum Output Volume Setting

Set the minimum threshold for output volume.

Outline and Connecting Diagrams

NT-48 RV Outline and Connections

Physical dimensions and wiring diagram for the NT-48RV model.

NT-72 RV Outline and Connections

Physical dimensions and wiring diagram for the NT-72RV model.

NT-10 Outline and Connections

Physical dimensions and wiring diagram for the NT-10 model.

Parameter Settings

Output Method Configuration

Select between Relay or SSR output methods.

Cycle Time Setting

Configure the ON/OFF control cycle time.

Auto Tuning (AT) Parameter

Parameter to enable or disable auto tuning status.

Proportion Band Setting

Set the proportional band for PID control.

Integral Time Setting

Configure the integral time for PID control.

Derivative Time Setting

Configure the derivative time for PID control.

Hysteresis Setting

Setting for hysteresis to prevent rapid switching.

Input Signal Selection

Select the type of input sensor signal.

Unit Selection (°C;°F)

Choose between Celsius or Fahrenheit temperature units.

Decimal Point Setting

Configure the display format for decimal points.

Input Shift Adjustment

Adjust the input signal by adding a shift value.

Input Span Adjustment

Adjust the input signal by multiplying with a span value.

Alarm Mode Configuration

Configure the operating mode for alarms.

Function Selection (Timer;Soft Start)

Select overall functions like timer or soft start.

Timing Mode Selection

Choose when the timing function starts (PV ≥ SV or Power ON).

Timing Unit Selection (Seconds;Hours)

Select the time unit for timing functions (seconds or hours).

Altronics FOTEK NT-RV Series Specifications