Amana Home Laundry Dryers

Questions and Answers

A
alexander53Aug 20, 2025
Why does my Amana Dryer take so long to dry clothes?
- H
  Helen GibsonAug 20, 2025
  Several factors can cause your Amana dryer to not dry clothes effectively. Make sure you are not overloading the dryer; a normal washer load should equate to a normal dryer load, and the maximum load should only fill half of the dryer cylinder with wet clothes. Also, ensure the lint filter is clean. If the load is too small, try adding one or two bath towels. For automatic cycles, adjust the timer to a MORE DRY setting. Other potential causes include too much water left in the articles being dried, a selector switch or timer that is incorrectly set or has failed, a cylinder belt not properly installed on the pulley, a failed moisture sensing control, or gas line pressure that is too high or too low.
K
Kristin WestAug 27, 2025
Why does my Amana Dryer stop in the middle of a cycle?
- M
  michael49Aug 27, 2025
  Your Amana dryer might stop mid-cycle due to several reasons. First, check if the dryer is overloaded; a normal washer load should be a normal dryer load, and the maximum load should be half of the dryer cylinder with wet clothes. Make sure that the voltage is correct by looking at the rating label inside the door well. Also, inspect the cylinder for any binding issues, such as out-of-round conditions, warping in the front and rear bulkheads, binding support rollers, worn or damaged cylinder seals and guides, or clothing stuck in the blower wheel or lodged between the cylinder baffle and bulkhead. A failed motor switch or a short in the motor winding could also be the cause; test the motor switch and windings, and replace the motor if it has failed.
D
Daniel WilliamsAug 28, 2025
What should I do if my Amana Home Laundry Dryers motor does not stop?
- A
  Amy EdwardsAug 28, 2025
  If your Amana dryer's motor won't stop, first check the wiring to the motor switch against the wiring diagram to ensure it's correct. A failed door switch, timer, or electronic control could also be the culprit; test each and replace if necessary. Additionally, a motor centrifugal switch that is sticky or plugged with lint can cause this issue; clean it and lubricate with “SLYDE”, part number 131P4.
F
fisherjenniferAug 30, 2025
How to fix an Amana Home Laundry Dryers Dryer when the burner ignites and goes out repeatedly?
- E
  Emily SullivanAug 30, 2025
  If your Amana dryer's burner ignites and then goes out repeatedly, it could be due to several reasons. First, verify that the gas shut-off valve is fully open and that proper gas pressure is being supplied to the unit. Test the ignitor and replace it if it is failed or cracked. Also, test the gas valve coils and replace them if they are failed or intermittent. Finally, test the flame sensor and replace it if necessary, and verify that proper gas pressure is being supplied to the unit.
M
Mercedes ElliottSep 1, 2025
What to do if the ignitor glows but the burner does not ignite in my Amana Dryer?
- J
  jamesandrewsSep 1, 2025
  If the ignitor in your Amana dryer glows, but the burner doesn't ignite, check the gas supply first. Make sure the gas shut-off valve is fully open and that the correct gas pressure is reaching the unit. Also, check the position of the ignitor and bracket to ensure they are properly installed. Test the gas valve coils and replace them if the secondary or holding coil is open. Additionally, test the flame sensor and replace it if its contacts have failed in the closed position. Ensure the flame sensor is correctly positioned as well.
J
julie02Sep 3, 2025
Why does the heater assembly shut off prematurely in my Amana Dryer?
- M
  Martin HernandezSep 3, 2025
  If the heater assembly or burner in your Amana dryer shuts off too soon, start by ensuring that the gas shut-off valve is fully open and that proper gas pressure is being supplied to the unit. Verify the dryer is equipped for the type of gas being used. Properly adjust the burner flame. Test and replace the limit thermostat if it is cycling off. Also, test the flame sensor and replace it if its contacts have failed in the closed position. Test and replace the timer or electronic control if they have failed. Additionally, test and replace the moisture sensing control if it has failed.
T
tatenormaSep 5, 2025
What to do if the Amana Home Laundry Dryers signal does not operate correctly?
- W
  Wendy ChangSep 5, 2025
  If the signal on your Amana dryer isn't working right, test and replace the moisture sensing control if it has failed. Also, test and replace the electronic control board, signal selector switch, or adjustable buzzer if any of them have failed. Finally, test the timer and replace if failed.
R
Robert FosterSep 9, 2025
How to resolve a heater assembly repeatedly cycling off on the limit thermostat in Amana Dryer?
- C
  christina16Sep 9, 2025
  If the heater assembly or burner in your Amana dryer repeatedly cycles off on the limit thermostat, start by cleaning the lint filter. Disassemble the ductwork and clean out any lint located internally. Also, disassemble and clean the external exhaust system to remove any lint or obstructions. Test the thermostat and replace it if it's cycling at too low of a temperature. Test and replace the thermistor if it has failed. Check and replace the loading door seal or door catch if there is an air leak. Check and replace the blower seal or cylinder seal if there are air leaks.
M
Matthew JamesSep 12, 2025
What causes the heater assembly in my Amana Home Laundry Dryers to not shut off?
- W
  William TuckerSep 12, 2025
  If the heater assembly or burner in your Amana dryer does not shut off, and the timer is in a heat cycle, test the motor switch and replace if failed. Also test the heater assembly and replace if it has shorted.
S
Shannon MartinezSep 13, 2025
Why is clothing too hot when removing from Amana Home Laundry Dryers?
- A
  amanda15Sep 13, 2025
  Clothing may be too hot when removed from your Amana dryer if it is taken out before the cool-down cycle is complete; allow the dryer to finish its cycle. Test and replace the cycling thermostat or thermostat heater if they have failed on the DELICATE cycle. If the timer is inoperative and not allowing a cool-down, test and replace it. Check and replace any failed seals in the loading door and front panel, between the front panel and front bulkhead, the blower cover and air duct, or between the cylinder and front or rear bulkhead. Test also the moisture sensor and replace if failed.

Summary

Important Information

Important Notices for Consumers and Servicers

Key warnings and responsibilities for users and service technicians.

Recognize Safety Symbols, Words, and Labels

Defines hazard symbols (DANGER, WARNING, CAUTION) and their meanings.

Important Safety Information

General Safety Precautions

Comprehensive list of safety guidelines for dryer operation, installation, and maintenance.

Introduction

Electrical Service Information

About Ground Wires

Explains the purpose of grounding wires and their color coding for electrical safety.

Installation Instructions

Grounding and Wiring Instructions

Provides guidelines for connecting the dryer to the electrical grounding system.

Gas Dryer Power Supply

Covers grounding requirements and plug connection for gas dryers.

Proper Grounding and Polarization of 120 Volts Wall Outlets

Illustrates correct wiring and polarization for 120V outlets for gas dryers.

Electric Dryer Power Supply

Details 3-wire and 4-wire plug connections for electric dryers.

Gas Connection Information

Instructions for connecting the gas supply, including safety warnings and what to do if gas is smelled.

Testing for Gas Leaks

Procedure for testing gas supply connections for leaks using soap suds.

Position and Level Dryer

Checking Burner Flame

Procedure for observing and adjusting the burner flame for proper combustion.

Adjusting Air Flow to Burner

Steps to adjust the air shutter for optimal burner flame appearance and performance.

Connecting Dryer to Exhaust System

Guidelines for connecting the dryer's exhaust duct to the outdoors for optimal performance.

Maximum Exhaust Length

Exhaust Directions

Exhaust System Materials

General Information

Dryer Operation

Component Testing Information

Heating element

Procedure to measure the resistance of the heating element and lists part numbers.

Gas valve

Procedure to measure the resistance of the gas valve coils (holding, booster, secondary).

Ignitor

Testing Timer Motor Triac Output Circuit

Burner System Operation

Electric Circuit to Ignition System

Temperature Settings

Unit with Fixed 3-Position Switch

Unit with Fixed 4-Position Switch

Internal Motor Diagram and Schematic

Motor Testing Procedures

Troubleshooting Procedures

1. Motor does not operate.

Diagnoses and resolves issues where the motor fails to operate.

2. Dryer stops in middle of cycle, quits after a couple loads, has a burning smell or cycles on motor thermal protector.

Troubleshoots common issues like stopping mid-cycle, burning smells, or thermal protector trips.

3. Motor operates but cylinder does not turn.

Diagnoses reasons why the motor runs but the cylinder does not rotate.

4. Motor does not stop.

Troubleshoots issues where the motor fails to stop running.

5. Ignitor does not glow, (gas supply sufficient).

Diagnoses why the ignitor fails to glow when gas supply is adequate.

6. Heating assembly does not heat or burner does not ignite.

Addresses problems where the heating system or burner fails to ignite or heat.

7. Burner ignites and goes out repeatedly.

Troubleshoots issues where the burner ignites but then repeatedly shuts off.

8. Ignitor glows but burner does not ignite.

Diagnoses why the ignitor glows but the burner fails to ignite.

9. Heater assembly or burner shuts off prematurely.

Troubleshoots scenarios where the heater assembly or burner shuts off before the cycle is complete.

10. Heater assembly or burner repeatedly cycles off on limit thermostat.

Addresses repeated cycling off of the heater or burner due to the limit thermostat.

11. Heater assembly or burner does not shut off.

Diagnoses why the heater assembly or burner fails to shut off as expected.

12. Clothes do not dry.

Troubleshoots common causes for clothes not drying properly in the dryer.

13. Signal does not operate correctly.

Diagnoses issues with the dryer's signal not functioning as intended.

14. Timer does not advance in AUTOMATIC cycle.

Troubleshoots why the timer fails to advance during an automatic drying cycle.

15. Clothing is too hot when removing from dryer.

Diagnoses why clothes are excessively hot upon removal from the dryer.

Disassembly Procedures

Control Hood Assembly

Electronic Control

Timer

Loading Door and Door Hinges

Door Reversal Procedure

Detailed, step-by-step instructions with diagrams for reversing the dryer door swing.

Front Panel

Cabinet Top

Front Bulkhead Assembly

Cylinder Belt

Cylinder Assembly

Steps for removing the entire cylinder assembly from the dryer.

Cylinder Rollers

Rear Seal

Rear Bulkhead and Heater Box

Steps for removing the rear bulkhead and heater box assembly.

Heating System

Gas Valve Regulator

Burner Tube, Ignitor, and Bracket

Instructions for removing the burner tube, ignitor, and bracket assembly.

Flame Sensor

Burner Housing and Heat Shroud

Limit Thermostat (Gas Models)

Heating Element (Electric Models)

Instructions for removing the heating element assembly from the heater box.

Limit Thermostat and Thermal Fuse (Electric Models)

Procedure for removing limit thermostat and thermal fuse from electric models.

Cabinet

Base

Thermistor or Thermostat and Heater

Motor and Exhaust Assembly

Impeller and Housing

Motor

Idler Pulley

Terminal Block

Terminal Block Terminals

Power Cord

Thank you for buying an Amana dryer!

Recognize Safety Symbols, Words, Labels

Defines hazard symbols (DANGER, WARNING, CAUTION) and their meanings.

Drying Clothes

2. Clean the lint filter before each use

Emphasizes cleaning the lint filter for efficient drying and preventing fire hazards.

3. Select FABRIC SELECTOR setting

6. Turn timer to desired setting

Features, Hints, and Care

Lint Filter

Importance and procedure for cleaning the lint filter after each load.

Exhaust System

Reversing the Door

Trouble Shooting

NOISE

Troubleshoots common dryer noises like vibrating, thumping, rattling, and clicking.

OPERATION

Troubleshoots common operational issues like dryer not running or not heating.

Long drying times

Addresses long drying times by checking exhaust system, overloading, sorting, and washer spin.

Lint

Troubleshoots lint-related issues like full lint filter, improper sorting, and overloading.

Static

Provides solutions for static cling, including using fabric softener and avoiding overdrying.

DISPLAY

Explains display error codes and status messages.