Amba RADIANT LARGE CURVED HARDWIRED - User Manual

RADIANT LARGE CURVED HARDWIRED
INSTALLATION INSTRUCTIONS
WARNINGS
Please read the following information before installing and using your heated towel rack
CAUTION
OPERATING INSTRUCTION
TOOLS REQUIRED
SKUS
INTEGRATED SWITCH
CONTACT
WARRANTY
• These units should be installed by a certified electrician in accordance with the National Electrical Code (NEC)and the Canadian Electrical Code (CEC).
• The unit requires a 120 volt, 60 Hz power source and should be installed on a GFCI protected circuit.
• Plug-in units should be connected to a grounded outlet with a minimum rating of 10 amps.
• Follow instructions to ensure he learned is securely fix the wall. Unit is designed for drying towels. Under no circumstances should anyone climb on or hang on unit.
• Unit is intended for indoor use only. Do not place units inside a shower, sauna, steam room, or wherever unit would be exposed to water.
• As this is a heating device, the surface temperature can increase depending on the ambient temperature in the room and the number of tiles apply to the unit.
• Overloading the unit can cause the unit to become extremely hot and they result in a burn it touched and or damage the towels.
• The fasteners provided with installation kit are for convenience only are not suitable for all installation conditions.
• It is the ultimate responsibility of the installer to ensure proper mounting hardware is employed in attaching the unit to the wall.
• After installation, connect electrical power.
• Remove the protective cover from the switch and turn it to the on position.
• The indicator light will glow red and the towel warmer will start to heat — allow 10–20 minutes to heat up.
• This towel warmer has been designed to run continuously-turn off the switch or unplug the cord in the tower is not in use for long periods of time.
• Never use an extension cord for plug-in models.
Two year limited warranty
with proof of purchase
will apply if all terms and
conditions of sale are met
and installation instructions
are adhered to.
FOR FULL WARRANTY AND
TERMS OF SALE VISIT:
www.ambaproducts.com/warranty
INCLUDED COMPONENTS
• The radiant collection features an
integrated on/off switch.
• Remove plastic cover after installation
• Switch is located on the bottom of the left
vertical bar.
• Press switch to power on unit.
• Switch will illuminate when on.
RWHL-CP | RWHL-CB
P - POLISHED | B - BRUSHED
TEL: 404-350-9738
PAGE - 1
! CAUTION —SURFACE OF UNIT IS HOT WHEN ON !
EMAIL:
customerservice@ambaproducts.com
www.ambaproducts.com
FAX: 404-355-0166
2 YEARS
THE WARRANTY COVERS
DEFECTS IN WORKMANSHIP
AND MATERIALS
PARAMETERPARAMETER
CONFORMS TO UL STD.499
CERTIFIED TO CSA STD C22.2 NO.64
TOWEL WARMER | MODEL: RWHL-C
RATED VOLTAGE: 120V~
RATED FREQUENCY: 60Hz
RATED POWER INPUT: 150W
SERIAL NO:
HOUSEHOLD USE ONLY
DO NOT IMMERSE IN WATER
HOT SURFACE: AVOID CONTACT
UTILISATION DU MÉNAGE SEULEMENT
NE PAS PLONGER DANS L’EAU
SURFACE CHAUDE ÉVITER CONTACT
CAUTION:

Summary

General Safety Warnings and Precautions

Installation Warnings

Units must be installed by a certified electrician, require a 120V/60Hz GFCI circuit, and plug-in units need a grounded outlet.

Operational Cautions

Device temperature can increase; overloading may cause burns or damage. Use caution with hot surfaces and avoid water exposure.

Product Components and Specifications

Included Components

Lists and illustrates the parts provided for installation, including screws and mounting hardware.

Tools Required

Specifies the tools needed for installation, such as screwdrivers and drills.

Warranty Information

Details the two-year limited warranty covering defects in workmanship and materials with proof of purchase.

Product Parameters

Lists technical specifications including voltage, frequency, power input, and certifications like UL STD.499.

Integrated Switch Description

Integrated Switch Operation

Explains the function of the integrated on/off switch, its location, and illumination when active.

Installation Steps

Step 1: Wall Plate Mounting

Details the placement and attachment of the wall plate using specified components and measurements.

Step 2: Towel Warmer Attachment

Illustrates how to attach the main unit to the mounted wall plate using provided hardware.

Step 3: Securing the Unit

Shows the final step of securing the unit, emphasizing not to over-tighten the set screw.

Step 4: Powering On

Instructs the user to turn the unit on using the integrated switch after installation.

Amba RADIANT LARGE CURVED HARDWIRED Specifications

General

Type	Towel Warmer
Mounting Location	Wall
Installation	Hardwired
Material	Stainless Steel
Finish	Polished
Shape	Curved
Size	Large
Category	Bathroom Fixtures
Brand	Amba
Collection	RADIANT