AME 67601 - Adjusting Torque Measurement; Proper Torque Application; Safety Warnings for Use

AME INTERNATIONAL - 2 - WWW.AMEINTL.NET AME INTERNATIONAL - 3 - WWW.AMEINTL.NET
297*210mm
150-600 Ft.Lbs / 200-750 Ft.Lbs
Do not use this wrench as a
hammer or pry bar.
22mm wrench
To avoid inaccurate torque,
do not fully remove the nut.
Release the adapter by pushing
or pulling from center of the head.
To torque, grasp the handle and push downward.
A break-a-way indicates that the desired pre-set
torque has been met.
Lubricate three points
frequently.
The handle should align with
the desired torque.
Using a 22 MM wrench, adjust
the torque measurement to the
desired torque.
Torque wrench mechanism will break-a-way when desired
torque is met. Do not continue to apply pressure after desired
torque is met.
※
※
230ft.lb
To avoid inaccurate torque or damage to
the tool, do not install
unnecessary
extensions.
297*210mm
150-600 Ft.Lbs / 200-750 Ft.Lbs
Do not use this wrench as a
hammer or pry bar.
22mm wrench
To avoid inaccurate torque,
do not fully remove the nut.
Release the adapter by pushing
or pulling from center of the head.
To torque, grasp the handle and push downward.
A break-a-way indicates that the desired pre-set
torque has been met.
Lubricate three points
frequently.
The handle should align with
the desired torque.
Using a 22 MM wrench, adjust
the torque measurement to the
desired torque.
Torque wrench mechanism will break-a-way when desired
torque is met. Do not continue to apply pressure after desired
torque is met.
※
※
230ft.lb
To avoid inaccurate torque or damage to
the tool, do not install
unnecessary
extensions.
297*210mm
150-600 Ft.Lbs / 200-750 Ft.Lbs
Do not use this wrench as a
hammer or pry bar.
22mm wrench
To avoid inaccurate torque,
do not fully remove the nut.
Release the adapter by pushing
or pulling from center of the head.
To torque, grasp the handle and push downward.
A break-a-way indicates that the desired pre-set
torque has been met.
Lubricate three points
frequently.
The handle should align with
the desired torque.
Using a 22 MM wrench, adjust
the torque measurement to the
desired torque.
Torque wrench mechanism will break-a-way when desired
torque is met. Do not continue to apply pressure after desired
torque is met.
※
※
230ft.lb
To avoid inaccurate torque or damage to
the tool, do not install
unnecessary
extensions.
297*210mm
150-600 Ft.Lbs / 200-750 Ft.Lbs
Do not use this wrench as a
hammer or pry bar.
22mm wrench
To avoid inaccurate torque,
do not fully remove the nut.
Release the adapter by pushing
or pulling from center of the head.
To torque, grasp the handle and push downward.
A break-a-way indicates that the desired pre-set
torque has been met.
Lubricate three points
frequently.
The handle should align with
the desired torque.
Using a 22 MM wrench, adjust
the torque measurement to the
desired torque.
Torque wrench mechanism will break-a-way when desired
torque is met. Do not continue to apply pressure after desired
torque is met.
※
※
230ft.lb
To avoid inaccurate torque or damage to
the tool, do not install
unnecessary
extensions.
297*210mm
150-600 Ft.Lbs / 200-750 Ft.Lbs
Do not use this wrench as a
hammer or pry bar.
22mm wrench
To avoid inaccurate torque,
do not fully remove the nut.
Release the adapter by pushing
or pulling from center of the head.
To torque, grasp the handle and push downward.
A break-a-way indicates that the desired pre-set
torque has been met.
Lubricate three points
frequently.
The handle should align with
the desired torque.
Using a 22 MM wrench, adjust
the torque measurement to the
desired torque.
Torque wrench mechanism will break-a-way when desired
torque is met. Do not continue to apply pressure after desired
torque is met.
※
※
230ft.lb
To avoid inaccurate torque or damage to
the tool, do not install
unnecessary
extensions.
297*210mm
150-600 Ft.Lbs / 200-750 Ft.Lbs
Do not use this wrench as a
hammer or pry bar.
22mm wrench
To avoid inaccurate torque,
do not fully remove the nut.
Release the adapter by pushing
or pulling from center of the head.
To torque, grasp the handle and push downward.
A break-a-way indicates that the desired pre-set
torque has been met.
Lubricate three points
frequently.
The handle should align with
the desired torque.
Using a 22 MM wrench, adjust
the torque measurement to the
desired torque.
Torque wrench mechanism will break-a-way when desired
torque is met. Do not continue to apply pressure after desired
torque is met.
※
※
230ft.lb
To avoid inaccurate torque or damage to
the tool, do not install
unnecessary
extensions
.
Models 67601
& 67751
Break-A-Way
Torque Wrench
Instructions