American Legend AL1200W

Need help?

Do you have a question about the American Legend AL1200W and is the answer not in the manual?

Overview

Function Description
Important Technical Specifications
Usage Features
Maintenance Features

This document describes the American Legend 72 Inch X-Leg LED Air Hockey Table, a game table designed for indoor residential use.

Function Description:

The American Legend 72 Inch X-Leg LED Air Hockey Table is a recreational game table that provides an air hockey experience. It features an air motor to facilitate puck movement, LED rail lights for enhanced play, and an electronic scoreboard for tracking scores and game time. The table is designed for home use and offers various playing time options, sound adjustments, and a timeout feature. It can be powered by an A/C adapter for residential use or by batteries for store display purposes (with limitations).

Important Technical Specifications:

Model Number: AL1200W/F
Dimensions: 72 inches (length, implied by model name)
Power Supply:
- A/C Adapter (included, for residential use)
- 4 pcs AA Batteries (not included, for store display use only; powers LED playfield lights and electronic scoring, but not the air fan motor)
- 4 pcs AAA Batteries (not included, for strikers)
Hardware:
- H1: 8mm x 40mm Hex Head Bolt (12 pcs)
- H2: M8 Flat Washer (16 pcs)
- H3: M8 Lock Washer (16 pcs)
- H4: 3.5 x 35mm Phillips Flat Head Screw (14 pcs)
- H5: 8mm x 130mm Hex Head Bolt (4 pcs)
- T1: Socket Head Wrench (1 pc)
Main Components:
- P1: Main Cabinet with Air Motor & Puck Catchers (1 pc)
- P2: Universal Leg (4 pcs)
- P3: Decorative Leg Wooden Block (2 pcs)
- P4: Wooden End Block (2 pcs)
- P5: Top Panel of Lower Center Support Beam (1 pc)
- P6: Side Panel of Lower Center Support Beam (2 pcs)
Accessories:
- A1: LED Striker (2 pcs)
- A2: LED Puck (1 pc)
- A3: Puck (1 pc)
- A4: Felt Pad (2 pcs)
- A5: A/C Adapter (1 pc)
- A6: Table Leveling Shim (4 pcs)
- A7: Metal Corner Cap (pre-installed, 4 pcs)
Electronic Components:
- C1: LED Rail With Long Wire (1 pc)
- C2: LED Rail With Short Wire (1 pc)
- C3: Control Box (1 pc)
- C4: Sensor With Long Wire (1 pc)
- C5: Sensor With Short Wire (1 pc)
- C6: Air Motor (1 pc)
- C7: Scorer (1 pc)
- C8: Battery Box (1 pc)
- C9: LED Rail Cover (2 pcs)
Warranty: 90-day limited warranty for the original consumer purchaser.

Usage Features:

Assembly: Requires at least two capable adults for assembly. An electric screwdriver can be helpful but caution is advised to avoid overtightening. Four or more capable adults are required to lift and rotate the table into playing position due to its weight.
Power Modes:
- Residential Use: Primarily powered by the A/C adapter. The battery pack is not used or needed in a home environment.
- Store Display Use: Can be powered by 4 AA batteries (not included) for LED playfield lights and electronic scoring only; the air fan motor will not be powered by batteries. The A/C adapter should not be plugged in when using batteries.
Electronic Control Panel:
- Scoreboard & Air Motor ON/OFF: Press the POWER button to activate.
- LED Rail Light ON/OFF: Press the POWER button to activate.
- Playing Time Selection: Use UP/DOWN buttons to scroll through options (3, 5, 7, 10 Minutes, Tug of War, Free Play). Press PLAY to select and start.
- Sound Adjustment: Use UP/DOWN buttons during gameplay to adjust volume.
- Timeout/Pause Play: Press PLAY during gameplay to pause the clock.
- Reset: After a game, press any button (except POWER) to reset the scoreboard. Press and hold any button (except POWER) for 3 seconds to reset the scorer at any time.
- Auto Shut-off: The control box has an automatic turn-off feature after twenty minutes of inactivity (air motors and all electronics).
LED Puck Battery: Uses CR2016 Lithium Battery 3V. Lasts approximately 7 hours of continuous play. Not rechargeable. Turn switch to "OFF" when not in use to conserve battery life.
LED Striker Battery: Uses 4 pcs AAA Batteries (not included). Turn switch to "OFF" when not in use.
Table Leveling: Includes A6 leveling shims. Use a carpenter's level (two-foot level recommended) to adjust the table's height for a flat playing surface. Recheck level after 24 hours, especially on deep pile carpeting.

Maintenance Features:

Cleaning: Use spray furniture polish to clean all exterior surfaces. Apply spray furniture polish on the air hockey playing surface with the motor running to protect the surface and enhance puck speed.
Indoor Use: The product is intended for indoor use only.
Handling:
- DO NOT sit, climb, or lean on the table.
- DO NOT drag the table when moving it to prevent leg damage.
- DO NOT set drinks on the table.
Protection: Purchasing a table cover is recommended to protect and keep the table clean.
Battery Replacement (General):
- Replace batteries when electrical features work slowly or are not functional.
- Do not mix old and new batteries, or different types (Alkaline, Standard, rechargeable).
- Use Alkaline batteries for maximum performance.
- Do not use damaged batteries.
- Install new batteries according to polarity (+ & -).
- Do not short circuit battery terminals.
- Remove exhausted, leaking, or weak batteries during long periods of nonuse.
- Check battery terminals for cleanliness.
- Dispose of old batteries safely per local codes.
- Do not dispose of batteries into fire.
- If using rechargeable batteries, they must be charged under adult supervision and removed from the product before charging.
- Regularly examine battery chargers for damage.
- Remove batteries for extended storage.
- If local electrical interference occurs, move equipment away, reset (off/on or remove/reinsert batteries).
LED Light Strip Replacement: If LED lights are not working, first check A/C adapter connection to Junction Box and LED Rail light connections to Control Box. If still not working, disconnect A/C power and contact Customer Service for replacement parts. To replace, carefully pry the C9 LED Strip Cover out of the apron with a flat blade screwdriver, then disconnect and remove the C1 & C2 LED Light Strip. Install new strips, aligning male and female connectors, and connect to C3 Control Box Wire.