American Standard BAYECON101A - User Manual

Model:
BAYECON101A
BAYECON102A
BAYRLAY004A (Relay required in WC* Units)
Down Discharge Economizer and Rain Hood
Used with:
2/4TC*,WC*,YC*,DC* *018-036A
2/4TC*,WC*,YC*, DC* *042-060A
Inspect Contents
You must report damage and make claims to the transporta-
tion company immediately. Report missing parts to your sup-
plier immediately and replace with authorized parts only.
3. Install Economizer Assembly
Note: You must first install the filter rack per the instruc-
tions provided and then install the economizer.
2. Swing the return air damper section down so that it rests
on the bottom of the unit. The economizer will sit
completely over the return air opening in the bottom of
the unit. See Figures 5 on page 4. Screw the economizer
assembly together with one assembly screw in the side of
the economizer. Tighten the linkage rod between the
return air dampers.
3. Insert 2 screws through the holes in the front face of the
unit and into the matching attachment holes in the econo
mizer assembly. See Figure 6 on page 4.
4. Insert a screw through the pre-punched hole in the side
flange of the return air damper and into the mating hole
in the economizer assembly and tighten. See Figure 5 on
page 4.
18-HE39D8-7
Identify Economizer Kit Contents
Refer to Figures 1 and 2 on page 2 to identify the kit
contents.
Install Economizer Kit
General
The economizer is a multi-damper design. It is installed in the
return air stream and is connected to the unit low voltage sup-
ply through wire leads. The economizer is fully accessible
through the Coil access panel.
Important: The Economizer installation requires that you first
install an air filter rack ordered separately. Use:
BAYFLTR101A for 2/4YC*, WC*, TC*, DC* *018-3036A
BAYFLTR201A for 2/4YC*, WC*, TC*, DC* *042-3060A.
1. Remove Power
Disconnect and verify that power is off.
2. Remove Access Panels
Remove these four (4) access panels (see Figure 3, page 2):
• Control/Heat access panel
• Blower access panel
• Coil access panel
• Horizontal Return Air panel (discard or store)
When the economizer is installed in WC* models, relay
accessory kit BAYRLAY004A is required. Refer to the drawing
on page 9 to make your relay wiring connections in the Control
Box.
Installer’s Guide
ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES
IMPORTANT — This Document is customer property and is to remain with this unit. Please return to service
information pack upon completion of work.
HAZARDOUS VOLTAGE - DISCONNECT POWER BEFORE SERVICING
WARNING:
ELECTRIC SHOCK HAZARD
OPEN AND LOCK OUT ALL UNIT DISCONNECTS PRIOR TO
ACCESSORY INSTALLATION OR UNIT MAINTENANCE, TO
PREVENT INJURY OR DEATH FROM ELECTRICAL SHOCK OR
CONTACT WITH MOVING PARTS.
SAFETY HAZARD
DO NOT REMOVE END COVERS FROM ECONOMIZER AC-
TUATOR; THE SPRING-RETURN ASSEMBLY MAY RELEASE
AND CAUSE PERSONAL INJURY.
WARNING
!
!
WARNING
Use care when inserting the economizer in the return air com-
partment, to prevent damaging the foil faced insulation.
CAUTION
!
1. The economizer ships with the return air damper folded
up to allow the assembly to fit through the Coil opening
in the side of the unit, see Figures 1 and 2 on page 2.
Insert the economizer assembly into the unit through the
Coil access panel opening. See Figure 4 on page 3.

Summary

General Economizer Information

Economizer System Description

Details the multi-damper design and its connection to the unit's low voltage supply.

Economizer Kit Identification

Inspect Kit Components

Instructions for reporting damage or missing parts to the transportation company or supplier.

Economizer Installation Procedure

Prepare for Economizer Installation

Disconnect power and remove four specified access panels before installing the economizer.

Install Economizer Assembly

Insert and secure the economizer assembly into the unit via the Coil access panel.

Install Rain Hood Assembly

Mount Mixed Air Sensor

Mount the Mixed Air sensor to the partition using sheetmetal screws.

Route Main Wiring

Pass and route the wire harness through the unit's compartments and into the control box.

Complete Installation Steps

Complete wiring, power up, run checkout, and replace access panels.

Checkout Procedures

Motor Operation Checkout

Verify motor operation through its full open-close stroke and check for binding.

Enthalpy Checkout Procedure

Follow steps to verify sensor operation and motor response for enthalpy control.

American Standard BAYECON101A Specifications

General

Brand	American Standard
Model	BAYECON101A
Category	Air Conditioner Accessories
Language	English