66 ASC 70 / 90 / 100 / 110 / 130 / 150 / 200 / 250
6. Removing the engine
Motor oils and lubricating grease
Roller with engine Engine oil Amount [l gal]
ASC 70/90 TIER 1, ASC 100 TIER 1 API CE; SAE 15W/40 11,2 [2.96]
ASC 70/90 TIER 2 API CH 4/SJ, CI/SK; SAE 15W/40 11,2 [2.96]
ASC 70/90 TIER 3 API CH 4/SJ, CI/SK; SAE 15W/40 7,0 [1,85]
ASC 110 - 150 TIER 1 API CE; SAE 15W/40 16,3 [4.3]
ASC 110 - 150 TIER 2 API CH 4/SJ, CI/SK; SAE 15W/40 16,3 [4.3]
ASC 110 - 150 TIER 3 API CH 4/SJ, CI/SK; SAE 15W/40 11 [2.9]
ASC 200/250 TIER 1 API CE; SAE 15W/40 14,3 [3.78]
ASC 200/250 TIER 2 API CH 4/SJ, CI/SK; SAE 15W/40 14,3 [3.78]
ASC 200/250 TIER 3 API CH 4/SJ, CI/SK; SAE 15W/40 19,7 [5.2]
Coolant uid in engine
ASC 70/90 TIER 1, 2 19 [5.0]
ASC 70/90 TIER 3, ASC 100 TIER 1 24,0 [6.3]
ASC 110 - 150 TIER 1, 2 25 [6.6]
ASC 110 - 150 TIER 3 32 [8.5]
ASC 200/250 TIER 1-3 30 [7.9]
Lubricating grease
ISO 6743/9 CCEB 2
DIN 51 502 KP2K-30
Coolant is a mixture consisting of treated demineralized or distilled water and antifreeze ethylene glycol. Coolant can be also prepared
from a propylene glycol antifreeze. Minimum portion of the ethylene glycol or propylene glycol antifreeze in the coolant is 50 %.
Temperature limits of coolant at dierent contents of ethylene glycol or propylene glycol in the liquids used are given in the following
table:
antifreeze with ethylene glycol antifreeze with propylene glycol
50 % = –37 °C [–34 °F] 50 % = –33 °C [–27 °F]
60 % = –54 °C [–65 °F] 60 % = –49 °C [–56 °F]
68 % = –71 °C [–96 °F] 68 % = –63 °C [–82 °F]
Water for preparation of the coolant should be used according to the criteria given in the following table:
Water quality min. max.
pH factor at 20 °C [68 °F] 6,5 8,5
Content of chlorides (mg/dm
3
) - 100
Content of sulfates (mg/dm
3
) - 100
Total hardness (°dGH) 3 12
Liquids: The liquids used must contain anticorrosive additives protecting all materials in the cooling system including rubber and the
head gasket. Liquids should not be mixed together with those of other marks. They must correspond to testing criteria as given in
ASTM 4985. Do not use a greater portion of the frost proof cooling agent in coolant than 50 % if it is not necessary.
Never use proportion greater than 68 %.
MANUALEQUIPOSPESADOS.COM manualequipospesados@gmail.com
To Next Page
Loading...
