Ammann ATR 68 P - User Manual

34 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Trans la ti on of the Ori gi nal

ope ra ting in struc tions (EN)

Book ID: 2-00013021

ATR 60 P

ATR 68 P

Serial Nr. ########-

Honda GXR120RT

Serial Nr. ########-

Other manuals for Ammann ATR 68 P

Operator's Manual154 pages

Questions and Answers

C
Carol RussellAug 8, 2025
Why Ammann Construction Equipment engine does not start?
- S
  sarah90Aug 8, 2025
  There are several reasons why the engine might not start. It could be due to a closed fuel valve – ensure it is set to the «ON» position. Another reason could be an empty fuel tank – refill it. A faulty ignition spark could also be the culprit – replace the spark plug. Check that the ignition switch is set to «ON», and if it’s faulty, replace it. Finally, verify the engine oil level, as a low level can prevent the engine from starting.
C
Christopher JonesAug 13, 2025
What to do if Ammann Construction Equipment engine does not reach top speed?
- H
  hendrickskatherineAug 13, 2025
  If the engine isn't reaching its top speed, consider these possible causes: the throttle cable might be faulty and need replacement, or the gas cable adjustment may be incorrect, requiring adjustment. Also, a clogged air filter can restrict performance, so clean the filter cartridge or replace it. In some cases, the engine or carburetor itself may be faulty, necessitating replacement or repair.
A
Adam AlvaradoAug 17, 2025
What to do if Ammann Construction Equipment engine does not start when starter is operated?
- J
  Justin WhiteAug 17, 2025
  If the engine fails to start when the starter is engaged, the starter itself may be faulty and require replacement. Alternatively, a broken spring within the starter mechanism could be the cause, also necessitating starter replacement.
M
Mark WhiteAug 23, 2025
Why Ammann Construction Equipment tamper movement is irregular, jumps?
- J
  Johnny PerryAug 23, 2025
  Irregular or jumping tamper movement can stem from a few issues. The speed might be incorrect, so correct it. The springs could be broken and need to be renewed by Ammann Customer Service. Also, ensure the throttle lever is set to «max».
A
Angela MoodyAug 28, 2025
What to do if Ammann Construction Equipment engine runs at high speed, but no vibration?
- L
  Lisa ClarkeAug 28, 2025
  If the engine runs at high speed without producing vibration, the centrifugal clutch may be faulty and require replacement. Alternatively, the connecting rod might be broken, requiring renewal by the Ammann after-sales service.
W
William ButlerSep 2, 2025
How to fix Ammann Construction Equipment starter cable if reversing starter does not return to initial position?
- J
  James JohnsonSep 2, 2025
  If the reversing starter cable doesn't return to its initial position, it could be due to fouling, in which case cleaning the starter is recommended. Alternatively, a broken spring might be the cause, requiring replacement of the starter.

Summary

Safety Regulations

Intended Use

Operator Qualifications

Specifies age and authorization requirements for operators.

Technical Data

Noise and Vibration Data

Operation

Before Using

Motor Operation

Explains starting, running, and stopping the motor.

Working with the Tamper

Covers operating techniques and controls for effective tamping.

Maintenance

Maintenance Schedule

Provides a schedule of required maintenance tasks and intervals.

Lubrication Schedule

Maintenance Motor

Fuel System

Checking the Motor Oil Level

Procedure for checking and topping up motor oil.

Air Filter Maintenance

Maintenance Machine

Cleaning

Tightening Torque

Padfoot: Changing the Oil

Troubleshooting

Troubleshooting Table

Lists common faults, causes, and remedial actions.

Summary

Safety Regulations

Intended Use

Operator Qualifications

Specifies age and authorization requirements for operators.

Technical Data

Noise and Vibration Data

Operation

Before Using

Motor Operation

Explains starting, running, and stopping the motor.

Working with the Tamper

Covers operating techniques and controls for effective tamping.

Maintenance

Maintenance Schedule

Provides a schedule of required maintenance tasks and intervals.

Lubrication Schedule

Maintenance Motor

Fuel System

Checking the Motor Oil Level

Procedure for checking and topping up motor oil.

Air Filter Maintenance

Maintenance Machine

Cleaning

Tightening Torque

Padfoot: Changing the Oil

Troubleshooting

Troubleshooting Table

Lists common faults, causes, and remedial actions.

Ammann ATR 68 P Specifications

General

Brand	Ammann
Model	ATR 68 P
Category	Vibratory rammers & tampers
Language	English

Related product manuals

Ammann ATR 68 C

Preview: Ammann ATR 60 C

Ammann ATR 60 C

Preview: Ammann APR 2220

Ammann APR 2220

Ammann APR 2620

Ammann APR 3020

Ammann APR 3520

Preview: Ammann APH 5020

Ammann APH 5020

Preview: Ammann ASC Series

Ammann ASC Series