How to troubleshoot AmySystems R3 HD Hybrid when nothing works?
If your AmySystems Wheelchair isn't working, start by checking the batteries and ensuring they are properly installed. Next, verify that the 24V power cable is securely connected. Also, check the fuse and replace it if it's burned. If these steps don't resolve the issue, the switchbox may be defective.
Why does the fuse keep burning in my AmySystems Wheelchair?
If the fuse in your AmySystems Wheelchair burns repeatedly, a mechanical restraint might be the reason. Verify the mechanical assembly thoroughly. It may also be due to a short circuit in one of the cables, in which case you should call AmySystems technical support for further instructions. Another possible cause is a defective controller.
How to fix a noisy actuator on AmySystems R3 HD Hybrid Wheelchair?
If the actuator in your AmySystems Wheelchair is noisy when moving up or down, it could be due to a defective actuator. Another possibility is a mechanical restraint. Ensure the seat is aligned correctly and doesn’t interfere with the tilt actuator's rear when tilting. Also, check for and remove any mechanical restraints and eliminate any contact between the actuator and the power base frame.
What to do if AmySystems Wheelchair actuator doesn't operate, but relays can be heard?
If you hear the relays but the actuator isn't working on your AmySystems Wheelchair, it might not be connected to the controller. Verify the electrical assembly and programming thoroughly. It could also be a defective actuator, in which case you should call AmySystems technical support for further instructions. A defective controller is another possible cause.
Why is the drive defeat switch not working on my AmySystems Wheelchair?
If the drive defeat switch, mercury switch, or reduced speed function isn't working right on your AmySystems Wheelchair, it could be due to wrong programming. Verify the proper mechanical operation of limit switches and verify the electrical assembly and programming thoroughly. The drive defeat switch, the reduced speed switch, or the mercury switch could also be unplugged or defective.
What to do if AmySystems R3 HD Hybrid actuator only goes in one direction?
If the actuator on your AmySystems Wheelchair only goes in one direction (with DAC Controller), it may be due to wrong programming. Verify the electrical assembly and programming thoroughly. It could also be due to wrong cable plugging. If it still does not work, call AmySystems technical support for further instructions.
Why does the charger fuse burn when charging AmySystems Wheelchair?
If the charger fuse burns every time you try to charge the batteries of your AmySystems Wheelchair, ensure you are using the battery charger provided with your wheelchair. It may also be caused by trouble with the power interfacing cable.
Critical safety warnings for users and technicians regarding wheelchair operation and potential hazards.
Explains what EMI is and how it can affect wheelchair operation, potentially causing unintended movement.
Essential safety instructions for users, including joystick use, positioning, and hazard awareness.
Warnings regarding maximum weight capacity and the importance of adjusting controller settings.
Guidelines for safe transfers, reaching, and leaning to prevent falls or tip-overs.
Advice on navigating obstacles, ramps, slopes, and maintaining traction for safe operation.
Safety procedures for navigating curbs and single steps, recommending ramp use.
Strict prohibitions against using stairs and escalators with the wheelchair due to high risk.
Safety guidelines for power seating functions and accessories like tilt, lift, and recline.
Procedures for accessing batteries, understanding the joystick, and operating motor locks.
Guidelines for performance control settings and operating power seating via joystick.
Instructions for operating power tilt and understanding the drive lock-out feature.
Guides for seat elevator control and driving in reduced speed mode while elevated.
Combined tilt/elevate operation, reduced speed driving, and drive lock-out safety.
Instructions for operating power tilt using 4-way toggle and push button switches.
Procedure for adjusting the wheelchair's center of gravity for patient safety and stability.
Guidelines for using the battery charger and essential safety precautions to avoid damage.
Safety precautions for charging batteries to prevent shock, fire, or explosion.
General| Foldable | Yes |
|---|---|
| Seat Width | 40 cm |
| Seat Depth | 40 cm |
| Footrest | Adjustable |
| Frame Material | Aluminum |
| Color | Black |
To Next Page