To Next PageTo Next Page
Need help?Do you have a question about the ANALOX Ax60+ Multi-Gas and is the answer not in the manual?
Summarizes the use of WARNINGS, CAUTIONS, and NOTES in the service manual for hazard indication.
Provides critical safety warnings for operating and servicing the Ax60+ unit, emphasizing hazard avoidance.
Defines alarm names, descriptions, identification, and default setpoints for CO2 sensors.
Defines alarm names, descriptions, identification, and default setpoints for O2 sensors.
Explains how to set jumper links for sensor location in the Ax60+ system for proper hardware configuration.
Details the automatic power-on self-test (POST) sequence, including display messages and checks.
Introduces menus for viewing system configuration and sensor details without modification.
Describes how to view configured alarm setpoints for each sensor via the 'List Alrm pnts' menu.
Explains how to view alarm descriptions configured for each sensor via the 'List Alrm descs' menu.
Details the procedure for testing the functionality of Relays 1 and 2 to ensure they are operating correctly.
Describes checking the accuracy of CO2 sensors using a calibration check kit and gas.
Explains the two-point process (zero and span) for recalibrating CO2 sensors to ensure accurate readings.
Details the step-by-step procedure for performing a zero calibration adjustment on a CO2 sensor.
Details the step-by-step procedure for performing a span calibration adjustment on a CO2 sensor.
Describes checking the accuracy of O2 sensors using a calibration check kit and gas.
Explains the two-point process (zero and span) for recalibrating O2 sensors to ensure accurate readings.
Details the step-by-step procedure for performing a zero calibration adjustment on an O2 sensor.
Details the step-by-step procedure for performing a span calibration adjustment on an O2 sensor.
Describes checking CO2 sensors for the Ax60+ Kiosk using a calibration check kit and gas.
Explains the two-point process (zero and span) for recalibrating CO2 sensors for the Ax60+ Kiosk.
Details the step-by-step procedure for performing a zero calibration adjustment on a Kiosk CO2 sensor.
Details the step-by-step procedure for performing a span calibration adjustment on a Kiosk CO2 sensor.
Explains how to configure the number of attached sensors in the Central Display software.
Describes how to set the sensor display option for the Ax60+ Central Display.
Details how to enable or disable the evacuation function for specific alarms on the device.
Explains the configuration of relays R1 and R2 for triggering based on CO2 and O2 alarm events.
Describes the fail-safe configuration of the two relays in the Ax60+ central unit for safety.
Details the hardware specifications and external connection methods for relays R1 and R2.
Explains how to configure the fail-safe setting (Y/N) for Relay 1 in the Ax60+.
Explains how to configure the fail-safe setting (Y/N) for Relay 2 in the Ax60+.
Details how to configure Relay 1 to trigger automatically when a system fault occurs.
Details how to configure Relay 2 to trigger automatically when a system fault occurs.
Explains how to configure Relay 1 to trigger on specific sensor alarm events.
Explains how to configure Relay 2 to trigger on specific sensor alarm events.
Describes how to enable or disable alarms for specific sensors and alarm levels within the system.
Details how to configure specific sensor alarms to function as evacuation alarms.
Explains how to set the direction (high going or low going) for sensor alarms to be triggered.
Details how to enable or disable the audible sounder for specific sensor alarms.
Details how to enable or disable the visual strobe indicator for specific sensor alarms.
Explains how to configure sensor alarms to latch (remain active) or not latch after an event.
Details how to set the specific concentration thresholds for sensor alarms to trigger.
Lists fault codes, their descriptions, and recommended actions for troubleshooting Ax60+ system issues.
Explains how the Data Output Module (DOM) indicates faults using LEDs and status flags.
Details the port settings and communication protocol required for interfacing the DOM via Modbus.
Lists Modbus registers holding operation information for the DOM and Ax60+ system.
Explains how to change data output module node addresses using the PCB rotary encoder for MODBUS.
General| Measurement Range (Combustible Gases) | 0-100% LEL |
|---|---|
| Display | LCD |
| Operating Temperature | -20°C to +50°C |
| Gas Types Detected | Oxygen (O2), Carbon Monoxide (CO), Hydrogen Sulfide (H2S), Combustible Gases, Carbon Dioxide (CO2), Methane (CH4) |
| Measurement Range (Oxygen) | 0-25% vol. |
| Measurement Range (Carbon Monoxide) | 0-999 ppm |
| Measurement Range (Hydrogen Sulfide) | 0 to 100 ppm |
| Measurement Range (Carbon Dioxide) | 0-5% vol |
| Ingress Protection | Dust-tight and protected against water jets |
| Certifications | ATEX |
| Alarm Set Points | User-configurable |
