AJ-PCN082
Input: 100-240V~ 50/60Hz
Output: DC 24V 0.5A
<10W
>5h (High Mist)
>8h (Low Mist)
60 ml / 2.0 fl. oz (High Mist)
30 ml / 1.0 fl. oz (Low Mist)
300 ml / 10.0 fl. oz
2.4MHz
Model: AJPCN082
Anjou Aroma Diffuser
User Guide
Product Diagram
1
2
6
4
8
9
10 11
12
5
7
① Nozzle
② Tank Cover
③ Muting Cover
④ Essential Oil Tube
⑤ Water Tank
⑥ Drain Side
Specifications
Model
Power Adapter
Power
Working Time
Mist Output
Water Tank Volume
Ultrasonic Frequency
Package Contents
· 1 x Aroma Diffuser
· 1 x Power Adapter
· 1 x Cleaning Brush
· 1 x Essential Oil Tube
· 1 x User Guide
· 1 x Thank You Card
3
How to Use
Caution
1. Please add water to the tank first, then add essential oils up to the
marking on the tube or until dispensing starts. If there's no
fragrance, the water-oil balance may be off. Please add enough
essential oil as instructed then.
1H 3H 6H ON
2. It is recommended to use purified or distilled water.
3. Cinnamon essential oil is of higher density and viscosity than that
of water. When adding the cinnamon essential oil to the water, it will
sink to the bottom. It is recommended that the essential oil be
added directly on the water surface to accelerate diffusion.
Add and Drain Water
1. Remove the tank cover, add water into the tank no higher than the
max water level. Add a few drops of essential oil into the tube
until it spills out slightly. Put the tank cover back on.
3. Clean the water tank with the included brush when grime builds up.
Note:
Never pour essential oils into the tube when there is no water inside
the tank.
2. Drain excess water via the drain side if necessary.
1H 3H 6H ON
⑦ Timer Indicators
⑧ Base
⑨ Light Button
⑩ Timer Button
⑪ Power / Mist Button
⑫ Power Port
1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON
Timer Setting:
When the unit is on, press to set 1 / 3 / 6 hours
timer. The corresponding indicator will light up.
Timer OFF:
When the timer is on, press and hold for 2
seconds to turn off the timer at any time.
Automatic Color Changing:
Press once to enter automatic color changing
mode where 7 colors will be cycled through.
Select Color:
Press again to stay on the current color. Keep
pressing to cycle through different colors.
Press and hold for 2 seconds to turn off the mist.
Switch between High & Low Mist:
Press again to resume High Mist. Switch
between the two modes with each press.
Low Mist:
Press again to enter low mist mode with one
beep sound.
High Mist:
Press once to enter the default high mist mode.
Two beeps will sound and the ON indicator will
light up.
Operations and Functions
Connect to a power source. Once connected, the diffuser will enter
standby mode. Please make sure there is enough water inside the tank.
OperationsFunctions
Mist ON
Mist OFF
Timer
Setting
Light Mode
Setting
Low Water Protection
The diffuser will turn off automatically when water inside the tank has
been depleted. Once water is added back into the tank, the diffuser
will resume standby mode.
How to Clean
IMPORTANT!
Please unplug the unit before cleaning!
Regular Cleaning
1) Empty the tank from the water outlet.
2) Add 3-5g (approx. one teaspoon, based on scale of the residues)
baking soda / NaHCO3 to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for 3-5mins, wipe down the tank and tank cover using a small
brush or soft cloth with baking soda solution. (For better cleaning,
remove the muting cover and wipe it down thoroughly).
5) Drain the solution and rinse the tank under tap water.
6) Rub the inside and outside dry with a dry towel or clean cloth.
7) Wipe off the soda residues if any.
Deep Cleaning
You are recommended to deep clean your diffuser once a month or
when the mist output is low due to grime build-up.
1) Empty the tank from the water outlet.
2) Add 2-3 teaspoons of baking soda / NaHCO3, or 2-3 slices of fresh
lemon to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for about half an hour.
5) Thoroughly clean the grime at the bottom and atomizer (slot at the
center) of the tank with a small brush.
6) Wipe down tank cover using a small brush or soft cloth with baking
soda solution. (For better cleaning, remove the muting cover and
wipe it down thoroughly).
7) Drain the solution and rinse the tank under tap water.
8) Wipe off the soda residues if any.
9) Rub the inside and outside dry with a dry towel or clean cloth.
Notes:
1) You may use dishwashing detergent when baking soda is
unavailable. But it works better for oil removing instead of odor
and mineral buildup.
2) Do not rinse the base directly with water; try to avoid wetting the
buttons, light holes, air inlets and underneath to avoid short circuit.
3) It is not recommended to clean the unit with white vinegar since
its direct and indirect contact with the atomizer will damage it
permanently.
Troubleshooting
No. Problem Solution
1
The LED light is not
turned on when powered
on.
Press the Light Button to turn
on the light.
2
The unit stops misting
with the light flashing
red as over-temperature
alarm.
• Turn off the unit.
• Pay attention to the
environmental temperature
and place the unit in a
well-ventilated place to cool
down.
• Do not add warm water into
the tank.
3
The mist output is
becoming low.
• Keep the water clean or use
purified or distilled water.
• Clean the atomizer regularly.
4
Mist level is becoming
low, and finally stops
misting.
Add water if there is not
enough water in the water
tank.
5
Scales in the water tank
and water reservoir
Clean the unit as instructed in
the Cleaning and Maintenance
section.
6
Strange odor after long
idle time
Clean the unit thoroughly
before use.
No. Problem Solution
7
Previously used
essential oil smell
remains in the unit.
Clean the unit thoroughly
before use.
8 Diffusion not enough Turn on the High Mist mode.
9 Wet table surface
The mist level is too high for
the small space. Please lower
the mist level.
10
Fragrance not strong
enough
Add the essential oil into the
tube until it spills out slightly.
11
No fragrance after
adding cinnamon
essential oil
Cinnamon essential oil
is of higher density and
viscosity than that of water.
It is recommended that the
essential oil be added directly
on the water surface to
accelerate the diffusion.
12
Failed to select one
color
Press the Light Button once
to enter automatic color
changing mode. Press it
again to stay on the current
color. Keep pressing to cycle
through different colors.
ENEN
DE
Produktabbildung
⑦ Timer
⑧ Basis
⑨ Lichttaste
⑩ Ti me r-Ta s te
⑪ Power- / Nebeltaste
⑫ Stromanschluss
① Zerstäuberdüse
② Tankabdeckung
③ Dämpfende Abdeckung
④ Röhrchen für ätherische Öle
⑤Max. Wasserfüllstand
⑥ Seitenablauf
1 2 3 4 5 6 7 8 9 10
To Next Page
Need help?
General
