Anschutz 130-626.NG002

To Next Page

Anschütz GmbH

Zeyestr. 16-24

24106 Kiel

Germany

www.anschuetz.com

Operator Unit Gyro Compass

Operator and Service Manual

Type: 130-626.NG002

Edition: 001

10000001976

Main Page

Table of Contents3
List of Figures7
List of Abbreviations11
Introduction13
Preliminary Remarks13
Change History13
Safety13
General Safety Regulations13
Tab. 1: Change History13
Safety Regulations14
Electrostatic Discharge15
Fig. 1: Electrostatic Discharge, Protected Area15
Standard Compliancy16
List of Further Documents16
Tab. 2: List of Standards16
Tab. 3: List of Further Documents16
List of Annex Documents17
Tab. 4: Dimensional Drawings17
Tab. 5: Wiring Drawings17
Tab. 6: Configuration Sheets17
Description18
Purpose18
Technical Data18
Technical Description18
Serial Interface19
Fig. 2: Operator Unit, Flush Mounted19
Configurable Parameters21
Operating Elements and Indicators21
Fig. 3: Operating Elements and Indicators, Gyro Compass Selected21
Fig. 4: Operating Elements and Indicators, Magnetic Compass Selected23
Operating Elements and Indicators on CPU PCB24
Fig. 5: CPU PCB, Operating Elements and Indicators24
Operating Elements and Indicators on Connection PCB25
Fig. 6: Connection PCB, Operating Elements and Indicators25
Functional Description28
Dimming28
Quick Settling28
CAN Bus29
Fig. 7: CAN Bus, Block Diagram29
Gyro Compass System Remote Control30
General Error Messages30
Main Pages30
Fig. 8: Display Page: no CAN Connection30
Main Page: Overview31
Display Page: Gyro Compass Selected31
Display Page: Magnetic Compass Selected31
Main Page: Heading Monitoring / Service32
Fig. 9: Display Page: Heading Monitoring32
Display Page: Auto Heading33
Fig. 10: Display Page: Enter Service Mode33
Fig. 11: Display Page: Auto Heading34
Display Page: Speed Error Correction35
Fig. 12: Display Page: Speed Error Correction35
Display Page: DV-Bus36
Display Page: Speed Source du37
Fig. 13: Display Page: DV-Bus37
Fig. 14: Display Page: Speed Source du37
Display Page: Heading Uncorrected38
Display Page: Rate of Turn38
Fig. 15: Display Page: Heading Uncorrected38
Display Page: Deviation Table39
Fig. 16: Display Page: Rate of Turn39
Display Page: Gyro Data40
Fig. 17: Display Page: Deviation Table40
Fig. 18: Display Page: Gyro Data41
Display Page: CAN-Devices42
Fig. 19: Display Page: CAN-Devices42
Display Page: Software Versions43
Main Page: Heading and Rot43
Fig. 20: Display Page: Software Versions (Figure May Vary from Actual Device)43
Main Page: Rot / Roll / Pitch44
Fig. 21: Main Page: Heading44
Main Page: Alerts45
Fig. 22: Main Page: Rot / Roll / Pitch45
Bridge Alert Management46
Fig. 23: Main Page: Alerts, Unacknowledged46
Tab. 7: Alert List, Alarm Symbols47
Tab. 8: Alert List, Warning Symbols48
Tab. 9: Alert List, Caution Symbols48
Tab. 10: Alert Signaling48
Tab. 11: Acknowledge Not Allowed Symbols49
Operation50
Preliminary Remarks50
Safety Instructions for Operation50
Setting into Operation51
Pre-Operation Procedures after Longer Time Setting out of Operation51
Heading Indication from Gyro System after Switching on51
Fig. 24: Display Page: Heating Stage52
Fig. 25: Display Page: Settling Stage52
Activate Quick Settling53
Fig. 26: Display Page: Quick Settling Possible53
Fig. 27: Display Page: Quick Settling Activated53
Normal Operation Procedures54
General Settings54
Select a Menu54
Change Values54
Confirm Settings54
Adjust Brightness55
Color Modes55
Fig. 28: Display Page: Color Mode55
Select Display Synchronization and Color Mode for Day and Night56
Switch between Preset Day / Night Mode56
Perform Lamp Test57
Page Settings57
Change Current Sensor57
Fig. 29: Perform Lamp Test57
Change Speed58
Change Latitude58
Change Variation59
Set Heading Monitoring59
Set Threshold for Heading Monitoring60
Fig. 30: Display Page: Heading Difference60
Service Page Settings61
Open Service Mode61
Fig. 31: Display Page: Service Mode61
Set Switchover Auto Heading62
Fig. 32: Display Page: Service Mode, Submenus62
Fig. 33: Display Page: Auto Heading, Set Switchover62
DV Bus Settings63
Fig. 34: Display Page: Submenu DV Bus63
Connect DV Bus64
Assign DV Bus Address64
Change Speed Source du65
Fig. 35: Display Page: Speed Source du65
Edit Deviation Table66
Edit Deviation Table in a GG-R System66
Select Damping of Rate of Turn67
Set Speed Error Correction67
Emergency Operation Procedures68
Setting out of Operation68
Procedures for Longer Time Setting out of Operation68
Fig. 36: Display Page: Speed Error Correction, Restart Distribution Unit and Operator Unit68
Troubleshooting69
Safety Information on Troubleshooting69
Alert / Status Message Handling69
General Information on Alert Messages69
Supported Alerts and Their Properties70
Tab. 12: Operator Unit, Alert List70
Responsibility Transfer72
Temporary Silencing73
Interfaces73
Troubleshooting Table73
Tab. 13: Troubleshooting Table73
Installation77
Cable Connections77
Safety Instructions for Cable Connections77
General Remarks about Preparing Cable Connections78
Fig. 37: Prepare a Cable Connection78
Fig. 38: Prepare a Cable Entry79
Fig. 39: Example for Cable Connections79
General Remarks about Preparing Common Ground Connections80
Supply Voltage at Plug B980
Fig. 40: Prepare a Common Ground Connection80
CAN Bus at Plugs B7, B881
Fig. 41: Supply Voltage Connection at Plug B981
Status Output System Failure at Plug B482
Fig. 42: CAN Bus Connection at Plugs B7, B882
Fig. 43: Status Output System Failure at Plug B482
Serial in and Serial out at Plug B583
Fig. 44: Serial in and Serial out Connection at Plug B583
Relay Switching Outputs 1 to 4 at Plugs B6, B1184
Fig. 45: Relay Switching Outputs 1 to 4 at Plugs B6, B1184
Digital Inputs 1 and 2 at Plug B1085
Fig. 46: Digital Inputs 1 and 2 at Plug B1085
System Configuration86
Configuration of Serial Interfaces86
Configuration of Unit ID, CAN Group and CAN Number86
Tab. 14: Recommended CAN Settings According to Devices87
Care and Maintenance88
Safety Instructions for Installation and Maintenance88
General Information89
Reference to ISPC89
Special Tools, Measurement and Test Equipment89
List of Consumables89
Maintenance90
Maintenance Schedule90
Repair90
Tab. 15: Maintenance Schedule90
Transport and Storage91
Preservation, Packing and Storage91
Transport92
Disposal93
Spare Parts Catalog94
General Remarks94
Definitions94
Operator Unit94
Annex95
Definition of Proprietary NMEA Telegrams95
NMEA Telegram: PANZHDS95
NMEA Telegram: PANZSLD96
NMEA Telegram: PANZDAT96
Drawings97

Need help?

Do you have a question about the Anschutz 130-626.NG002 and is the answer not in the manual?

Anschutz 130-626.NG002 Specifications

General

Brand	Anschutz
Model	130-626.NG002
Category	Control Unit
Language	English

Anschutz 130-626.NG002 - User Manual

Table of Contents

Anschutz 130-626.NG002 Specifications