Ansul AUTOPULSE IQ-396X - Reading Specific Point and Zone Status

AUTOPULSE IQ-396X Programming Doc. 50402:B 07/22/96 19
Toggle the TERM_SUPERV, LocT,
ST-4/ST-6, and ACS functions by
pressing the Next and Previous
keys.
System Function Screen
The following table contains settings for general system functions.
System Function
Programming
0=CLR 1=AUTO 2=POINT 3=PASSWD 4=MESSAGE
5=ZONES 6=SPL FUNCT 7=SYSTEM 8=CHECK PRG
7
The System option lets you set general system functions. From the
Program Change screen, select <7> to display the System Function
screen.
Annunciator Selection 1 Screen
Use the Annunciator Selection screen to select information that will
display on the ACS annunciators. The following table contains the ACS
display selections.
Continued on the next page...
noitcnuFmetsySgnitteStluafeD
)emittibihnIecneliS(HNILISsdnoces003ot00
)emitecneliSotuA(OTUA)enon(orez
sdnoces009ot006
0
noitacifireVmralA(YFIREV
)emit
sdnoces03ot00
EMITASUsuoiverP/txeNhtiwemitRUE
syek
segnahctamrofemitnaeporuE
ehtsecalpdna,emitruoh-42ot
htnomehterofebyad
emitASU
VREPUS_MRETseYrooNoN
eerhtfoenoedomlanimreT
roCPfosedomgnitarepo
ehtotdetcennoclanimret
no2BThguorhtlenaplortnoc
etelpmocaroF.004-UPCeht
ehtotrefer,snoitcnuffotsil
.launaMnoitallatsnI
otdetcennoclanimret(TcoL
nidetacoldnalenaplortnoc
;)mooremas
tubTcoLsaemas(McoL
seriuqer
ro;)drowssap
detcennoclanimret(TmeR
daeRrofmedomahguorht
.)ylnosutatS
TcoL
)knilbDELecived(Y=KNILByb)knilbon(N=knilBotteS
.syeknwoD/pUehtgnisserp
Y=knilB
elytsgniriwAPFNeht4=TS
.poolCLSehtrofdesu
)gniriwpoolCLS6elytS(6=TS
)gniriwpoolCLS4elytS(4=TS
4=TS
noitceleSSCAesUSCA
ehtotrefer(spuorG
roflaunaMnoitallatsnI
YroNN=SCA
Setting General System Functions
If UDACT=N, the control panel displays the Annunciator Selection 2
Screen, addresses A11A19:
ANNUN SELECTION2 A11=* A12=* A13=*
A14=* A15=* A16=* A17=* A18=* A19=*
Annunciator Selection 2 Screen
Setting ACS=Y displays the Annunciator Selection 1 Screen, address
A1A10. If UDACT=Y, you can use addresses A11-A19 with UDACTs
having software release #UDACT01.0 or higher to send panel status to
a UDACT.
SIL INH=000 AUTO=000 VERIFY=00 USA TIME
TERM_SUPERV=NO LocT BLINK=Y ST=4 ACS=N
A=ACS Address
ANNUN SELECTION1 A1=* A2=* A3=* A4=*
A5=* A6=* A7=* A8=* A9=* A10=* UDACT=N
ACS Selection Group (1-9) or *=not selected