Ansul AUTOPULSE IQ-396X - Operating Time Functions; Time Functions and Real-Time Clock Usage; Operating Coding Functions for NACs

10 AUTOPULSE IQ-396X Operations Doc. 50403:B 07/22/96
Operating Time Functions
The control panel includes a real-time clock that provides time-of-day, date,
and day-of-week. The clock includes a lithium battery backup. Time
normally displays in a 12-hour time format with month/day/year. Figure13
contains descriptions and typical uses for time functions.
emiT
noitcnuF
noitpircseDsesUlacipyT
lortnoCemiT
dnammoC
devreserera6Fdna5FsenoZ
laicepsemit-yb-lortnocrof
rofdednetni,snoitcnuf
)erif-non(yrallicna
gnithgilsahcus(snoitacilppa
,tatsomrehtagnittes,lortnoc
.)htrofosdna
senozmargorp,elpmaxeroF
enotaetavitcaot6Fdna5F
taetavitcaeddnayadfoemit
syadniatrecno,emitrehtona
anrutnacuoY.keewehtfo
dnanotnioplortnocerif-non
.6Fro5Fenozgnisuyb,ffo
thgiN/yaD
ytivitisneS
tsujdA
EBCrotcetedXDSroXPCafI
lortnoceht,6Fro5Fenozstsil
rotcetedehtsteslenap
muminimehtotytivitisnes
ro5Fenoznehwgnittes)wol(
ehtybdetavitcasi6F
stiniemit/etaddemmargorp
6Fro5FenoznehW.EBC
rotcetedeht,setavitcaed
ehtotsnruterytivitisnes
,esuytivitisnesthgin/yadroF
sa6Fdna5Fsenozredisnoc
.senozYAD
yadiloHsevreserlenaplortnocehT
yadilohgnittesrof7Fenoz
ehtnehW.)syad9otpu(setad
foynasehctametadtnerruc
eht,setadyadilohenineht
enozsetavitcalenaplortnoc
7FenozrofsesurehtO
raey-fo-yadlaicepsa:edulcni
niyadht8naro;lortnoc
dna5Fsenozgnimmargorp
.6F
Figure 13: Control Time Functions
Zone F8reserved for NAC coding functionsis only used by panel NAC
circuits listing zone F8. You can select one of the type codes in Figure 14:
edoClangiS
emiThcraM
)tluafed(
)etuniMrePsesluP(MPP021
egatS-owT:langismralalareneG;MPP02langistrelA
noydaetS
ainrofilaCstaeper,ffo.ces5,no.ces01
laropmeT,ffo5.1,no5.0,ffo5.0,no5.0,ffo5.0,no5.0
Figure 14: Zone F8 Type Codes
 CMX modules  Zone F8 does not work if listed in the CBE of CMX mod-
ules.
 Two-Stage  When an alarm occurs, an NAC programmed for two-stage, and
not activated by another zone, pulses at 20 PPM. After 5minutes, the NAC
changes to steady on unless you press <Acknowledge/Step>. Pressing
<Alarm Activate> on the control panel changes the NAC pulse to steady.
ICM-4/ICE-4 modules do not support Two-Stage and turn on steady.
 ICM-4/ICE-4 modules  To enable California Code, cut D35 on the ICM-4
modules. If D35 is not cut, ICM-4/ICE-4 modules turn on steady.
Operating Coding
Functions
Notes on using Zone F8
Overview
Time Functions