12 /2 4H
PR OGR AM MAB LE TI MER
DAY
HR
MIN
SEC
CLOCK
Se le ct
St ar t/ Pa us e
RES ET CLEAR
On/Auto/Off
PROG.
MODE
APT1-S
WEEKLY PROGRAMMABLE TIMER
MANUAL
CAUTION
Do not contact the terminal when the power ON.
This may be caused by an electric shock or personal injury.
terminal cover must be installed after the wiring.
Do not use in places with inflammable and explosive gases.
1. Have the Timer installed only by qualified electrical workers.
2. Use the Timer within the specified ratings for operating
temperature and humidity.
3. The Timer is not waterproof or oil resistant. Do not use it in
locations subject to water or oil.
Do not use the Timer in locations subject to excessive dust,
corrosive gas, or direct sunlight.
4. Be sure to wire the terminals correctly and correct polarity.
5. Take adequate protective measures (such as a breaker, or
fuse)for the power supply of the Timer.
6. Do not touch the input terminal while power is being
supplied; touching live terminals may result in electric shock.
ANV ELECTRIC
NOTICE
DIMENSIONS
WARNING
Indicating a message , If not complied, May cause a
misoperation to cause a person to receive Damage
or property damage.
This product contains battery ! battery may be in danger of
leaking or explosion and causing personal injury.
Do not use the product at temperature of more than 55 degrees
Celsius. Do not contact with liquid.
Battery life depends on the usege.
Tighten the terminal screws to the rated torque.
Please cut off the power of the load or manual output to OFF
and confirm the security of the system before changing the
setting. Otherwise, it may cause damage to the machine.
Serious injury may occasionally occur due to fire or explosion of
a battery, or leakage from a battery. Never attempt to short the
positive and negative terminals, recharge, disassemble, deform
by applying excessive pressure, or expose the battery to fire.
When switch to Auto mode from ON
or OFF, output contact will be kept in the previous mode.
Than, output contact will be controlled by program setting.
SPECIFICATIONS
PARTS DESCRIPTION
DISPLAY DESCRIPTION
1
2
3
4
5
6
7
8
9
10
1 1
LCD Display
Output Indicator
Clock Key
Week Key
Hour Key/ 12/24H Key
Minute Key
Second Key /
Select Key
Manual Output Key /
Start Key / Pause Key
Program Key
Clear Key
Reset Key
ON: Green light OFF: Red light;
Shift key of clock setting
Weekday setting
Hour setting /
Change clock mode 12H/24H
Minute setting
Keep output cantact state open or close /
Start program ; Star or pause program in twin timer mode
Clear setting
Hold down 2 seconds to reset and restore manufature default
Display working status (See DISPLAY DESCRIPTION table)
Second setting /
Memory and backlight option select key
SYMBOL
NAME
FUNCTION
Program number setting Maximum of 80 programs ON/OFF;
Display hours minutes and seconds,
Display weekly
Display program ON or OFF
Display program number
Display AM or PM
Display output status
DESCRIPTION
1
2
3
4
5
6
SYMBOL
100~240VAC/DC 12~60VDC/AC 50/60Hz;
250VAC 15A Resistive load
ON Green OFF Red: ; :
-10 ~+50℃ ℃
45~85%RH
Approx. 3VA
Approx. 130g
Weight
Ambient Temperature
Ambient Humidity
Power Consumption
Dielectric Strength
Life
Rated Voltage
Voltage Range
Rated 90~110%
10 00V AC for 1 m in ut e be tw een input termina ls a nd c as e( ground)
15 00V AC for 1 m in ut e be tw een output t er mi na ls an d case(ground)
Contact Rating
Indicator Operating
Backlight
Mechanical: 5000000 times
Electrical: 100000 times
7
TIME ADJUSTMENT
Display twin timer mode
1 2
Mode Key Mode function setting
Press key key+
set the current weekday.
Press key key+
set the current hour.
Press key key+
set the current minute.
Press key key+
set the current second.
1
3
2
4
5
7
6
5.5
65.0
48.8
48.8
13.0
13.0
100.8
35.8
32.2
Y-50
US-08
APT1 + Y-50 + US-08
Surface P2CF-08:
Flush Y-50+US-08 Y-50+P3G-08: ;
Mounting & Socket
With Backlight
12 /2 4H
PR OGR AM MAB LE TI MER
DAY
HR
MIN
SEC
CLOCK
Se le ct
St ar t/ Pa us e
RES ET
CLEAR
On/Auto/Off
PROG.
1
6
7
9
1 1
5
4
3
10
2
12
MODE
8
To Next Page
Need help?
General