Anywire BL287SB-02F-CC20 - User Manual

BL287□B-02F□-CC20
LINK
ALM
-BL287*B02F*CC20 1/16-
Ver.1.1
[Type]
AnyWireASLINK System Products Guide
ASLINKER
■ Note on use ⇒ A separate Address Writer is required to set addresses and other data.
*
For more information, refer to [Various Settings] on page 9.
NPN input
NPN output
PNP input
PNP output
NPN input/NPN output
PNP input/PNP output
A WARNING indicates a potentially hazardous
situation which, if not handled correctly, could
result in death or serious injury.
[Warranty]
■ Warranty period
The warranty on the delivered Product shall continue to be effective for one (1)
year after the delivery thereof to a location as designated by the original owner.
■ Scope of warranty
Should a defect occur in any part of the Product during the foregoing warranty
period when it is used normally in accordance with the specications described
in this Products Guide, the Company shall replace or repair the defect free of
charge, except when it arises as a result of:
[1] Misuse or abuse of the Product by the owner;
[2] Fault caused by other than the delivered Product;
[3] The unauthorized modication or repair of the Product by any person other
than the Company’s personnel;
[4] Any unusual force of nature, disaster or other cause beyond the Company’s
control.
The term “warranty,” as used herein, refers to the warranty applicable to the
delivered product alone. The Company shall not be liable for consequential or
incidental damages resulting from any malfunction.
■ Repair at cost
After the expiration of the warranty period, the owner shall be responsible for all
costs and expenses incurred for the troubleshooting and repair of the Product.
Even during the warranty term, the Company shall repair any defects arising
from causes other than within the scope of the warranty as specied above, at
the owner’s cost.
■ Changes in the product specications and the descriptions in the manual
The descriptions in this manual may be subject to change without notice.
Precautions that must be observed in order to use this system safely are indicated as shown below.
You must observe these precautions.
[Notes on Safety]
A CAUTION indicates a potentially hazardous situation
which, if not handled correctly, may result in personal
injury or property damage.
CAUTION
WARNING
○ System power supply
Use a stable, 24V DC power supply. Use of an unstable power supply may cause problems with the system.
○ Separately route high-voltage and power cables
Although the AnyWireASLINK has a high noise margin, install the transmission line and I/O cables away from high-voltage and power
cables.
○ Connectors and terminals
- Pay careful attention to the length and installation of cable wiring to ensure that connectors and cables are neither overloaded nor disconnected.
- Make sure to prevent any metal objects from getting inside the connectors or the terminal blocks.
- Short-circuits caused by metal objects or mis-wiring are likely to damage the device.
○ Do not impose any external loads on the units. Doing so may cause a failure.
○ Do not disconnect or reconnect between the transmission line and slave units when the transmission line is active. A malfunction may occur.
○ Use the AnyWireASLINK within the range of the specications and conditions shown below.
○ System Safety
This system is intended for general industrial applications. It does not have functions for supporting applications requiring higher
levels of safety such as safety-related devices or accident prevention systems. The product must not be used for these purposes.
○ Always turn off the power in installing or replacing the system.
○ Prolonged continuous ow of a rated load current or higher or a transit current due to load short-circuit, etc., in the hybrid unit including
the output unit and the output circuit may result in smoking or ring. An external safety device such as a fuse must be installed.
CAUTION
WARNING
[About Pictogram
*
1
]
Ver. 1.0
*
2
Compatible with
Ver. 1.1
*
3
*
1 The pictogram may not be marked (or stuck) depending on the product.
*
2 AnyWireASLINK device not compatible with Ver. 1.1 (word transmission and
single unit simplified replacement functions)
Some products, not marked with the Ver. 1.1 pictogram, are compatible with
the functions included in Ver. 1.1. Refer to the lot No. and the product guide
for ultimate confirmation.
*
3 For details of Ver. 1.1, refer to the subsequent pages.
BL287SB-02F-CC20
BL287PB-02F-CC20
BL287XB-02F-CC20
BL287SB-02FS-CC20
BL287PB-02FS-CC20
BL287XB-02FS-CC20

Summary

Notes on Safety

System Safety

Intended for industrial applications; not for safety-critical systems.

System Power Supply

Use a stable, 24V DC power supply to prevent system issues.

Cable Routing

Install transmission and I/O cables away from high-voltage/power cables for noise margin.

Connectors, Terminals, and Load Limitations

Handle wiring carefully, prevent overloading, avoid metal objects in terminals, and do not impose external loads.

Warranty

Warranty Period and Scope

Covers one year from delivery for defects, excluding misuse or external causes.

Repair at Cost

Owner responsible for costs after warranty or for non-covered defects.

About Pictogram

About AnyWireASLINK Ver. 1.1

New Functions and Lot Number Changes

New functions like Word transmission and Single unit simplified replacement added from May 2019.

About Lot No.

Lot Number Format and Meaning

Lot numbers indicate year, month, and function/S/W/H/W versions.

About Word Transmission

Functionality and System Requirements

Master unit supports word data transmission; requires compatible slave units.

About Single Unit Simplified Replacement

Function and Procedure Overview

Enables automatic settings for slave unit replacement without an address writer.

Compatibility and Limitations

Requires compatible units, correct model/version, and specific address for function to work.

Function Version Identification

Function version is indicated on the lot label, showing updates or changes.

Functions

Function List and Detection Capabilities

Lists models, functions, connection targets, and status detection features.

Function Compatibility by Lot No.

Lot-based Function Variations

Available functions and specifications vary based on lot number due to version upgrades.

Lot Number Checking

Lot number is indicated on the back of the unit, showing model, date, and versions.

How to Connect AnyWireASLINK

Terminal Selection and Wiring

Choose two-wire or four-wire terminals based on load current and connection needs.

System Configuration Example

System Configuration Examples

Wiring examples for sensors (3-wire, 2-wire) and output devices.

Transmission Line and Supply Current Limits

Guidance on transmission line size, length, and allowable supply current.

Installation Location Guidelines

Specifies suitable installation environments, avoiding dust, vibration, and noise.

Notes on Use of 4-Wire (Isolated) Terminal

ASLINK Filter for Long Lines

Recommends ASLINK filter for long parallel runs of DP, DN, 24V, OV lines to improve noise resistance.

COSEL Filter Option

Alternative filter option for improving noise resistance and signal stability.

System Power Supply Diagrams

Diagrams showing system-wide and local power supply connections with filters.

COSEL Co., Ltd. Type: EAC-06-472 Connection Example

EAC-06-472 Filter Connection Diagrams

Diagrams for system-wide and local power supply using the EAC-06-472 filter.

Name of Each Part

Input, Output, and Mixed Unit Components

Details components, wiring, and LED indicators for input, output, and mixed units.

Connection Method

LP Connector Fitting Procedure

Step-by-step guide on how to fit the LP connector to the transmission line.

Various Settings

Address Setting Procedure and Precautions

Explains address writer operation, setting addresses, and important warnings.

Data Configuration

Address Offset and Bit Assignment Details

Shows address offset and bit assignment for different unit types.

Status Details and Alarm Checking

Explains how to check alarm contents via the "status detail area" on the master unit.

Monitor Display

LED Indicators and Error Interpretation

Details the meaning of LED indicators (LINK, ALM, I/O) and their display statuses for error identification.

Troubleshooting

Troubleshooting Common LED Indicators

Guides on resolving issues indicated by LINK not flashing, ALM lit, or ALM flashing.

Alternating Flashes and Mismatch Errors

Addresses issues with alternating LINK/ALM flashes and model mismatch errors during replacement.

Configuration and Electrical Characteristics of NPN Input;Output Circuits

4-Wire NPN Input;Output Characteristics

Details circuit conditions and electrical characteristics for 4-wire isolated NPN input/output units.

Configuration and Electrical Characteristics of PNP Input;Output Circuits

4-Wire PNP Input;Output Characteristics

Details circuit conditions and electrical characteristics for 4-wire isolated PNP input/output units.

Specifications

General and Individual Specifications

Covers operating conditions, occupied points, response time, current, weight, and transmission specs.

ASLINKER Cable Specifications

Provides details on the transmission and I/O side specifications of the included ASLINKER cable.

ADP-87 (Mounting Adaptor)

Mounting Adaptor Dimensions

Shows the dimensions and connection hook details of the ADP-87 mounting adaptor.

中国版RoHS指令

Hazardous Substance Information

Lists hazardous substances and their content levels in parts, complying with SJ/T11364-2006.

Address

Company Contact Information

Provides headquarters and contact details for Anywire Corporation.

Anywire BL287SB-02F-CC20 Specifications

General

Brand	Anywire
Model	BL287SB-02F-CC20
Category	Touch terminals
Language	English