Apec Water Ultimate Series User Manual

5
THERE ARE TWO PARTS TO INSTALLING THE RO SYSTEM:
Part I. Assemble the filters and housings onto the main system
Part II. Installing the system
Note: The RO Membrane Element has already been pre-installed.
PART I. ASSEMBLE THE FILTERS AND HOUSINGS ONTO THE MAIN SYSTEM
Remove plastic/paper wrappings on the 3 filters, put them into the 3 housings, and assemble the
housings onto the main system as follow:
1. See
Fig. 2 Stand the 3 housings upright. Make sure each housing has a rubber O-ring in its
groove.
Put the APEC Sediment filter (1-SED10) into the “1
st
stage” housing on the right.
Put the APEC Carbon filter (23-CAB10) into the “2
nd
stage” housing in the middle.
Put the APEC Carbon filter (23-CAB10) into the “3
rd
stage” housing on the left.
2. See
Fig. 3 Starting from the 3
rd
stage housing on the left, hand twist the housing onto the main
system turning counterclockwise, one by one, for all 3 housings.
3. See
Fig. 4 Use the wrench provided to completely tighten the housing starting from 1st-stage.
Repeat this step for the 2
nd
stage housing in the middle, and for the 3
rd
stage housing
on left.
Note: For some people it is easier to use the wrench with the system laid down
(face up).
4. See Pg. 3 Remove 2 end plugs (white color) from Point 10 & 12
Fig. 2
Fig. 3
Fig. 4
turn counter-clockwise
to tighten
3rd
Stage
3rd
Stage
2nd
Stage
1st
Stage
Use
Wrench
Use
5
T
T
H
E
E
R
R
E ARE TW
O
PART
S
T
O
IN
S
T
A
A
L
L
L
L
I
I
N
N
G
THE R
O
S
Y
S
TEM
:
P
a
rt I.
A
ssemble the
f
il
te
e
rsrs
a
a
ndnd
d
h
ousings onto the main syste
m
Part II.
I
nstalling the sys
te
e
e
mm
N
ote: The RO Membrane Element has already been pre-installe
d.
PART I. A
SS
EMBLE THE FILTER
S
AND H
OUS
IN
GS
O
NT
O
THE MAIN
S
Y
S
TE
M
R
emove pla
st
t
icic
/p/p
ap
a
a
er wrappings on the 3
f
ilters, put
t
he
he
h
m
m
in
in
to the 3 housings, and assemble th
e
e
housings
o
o
nt
nt
oo
th
th
e main system as
f
ollow
:
1
.
S
eeee
Fi
Fi
g
g.
2 Stand the 3 housings upright.
Ma
Ma
ke
ke
k
sure each housing has a rubber O-
ri
ri
i
ngng
i
i
n
n
it
it
s
groo
v
e
.
P
ut the APEC Sediment
f
i
lt
lt
e
er
(
(
1-
1
SED10) into the “
1
st
stage” housing
on
n
t
t
he
he
right.
P
ut the APEC Carbon
fi
fi
lt
lt
er
er
(
(
(
23
2
-CAB10) into the “
2
n
d
stage”
ho
o
usus
in
in
gg
in
n
the middle.
P
ut the APEC Car
bo
bo
n
n
fifi
lt
lt
er
e
(23-CAB10) into the “
3
rd
stage”
ho
ho
us
us
us
inin
g
g
on
o
the le
f
t.
2
.
See
Fig. 3 Starting
f
ro
o
m
m
th
e
e
3
3
d
rd
stage housing on the le
f
t, hand twist the housing onto the main
s
ystem
t
t
urur
u
ni
ni
ngng
c
c
ounterclockwise, one by one,
f
or all 3 housings.
3
.
See
Fig. 4
U
se the
wr
wr
en
en
ch
provided to completely tighten the housing starting
f
rom 1st-stage.
R
epeat this step
f
or the
2
n
d
stage housing in the middle, and
f
or the 3
r
d
stage housi
ng
g
o
n l
ef
t.
N
ote
:
For some people it is easi
er
t
t
o o
usus
e e
t
th
e wrench with the system laid
do
o
wn
wn
(f
ace
up
).
4.
4.
S
S
ee
Pg. 3
R
emove 2 end plugs (whit
e
e
coco
lo
lo
r)
r)
f
rom Point 10 & 12
F
i
g.
2
FiFi
g.
3
FiFi
g.
4
4
4
t
urn coun
t
er
-
cl
oc
k
wi
se
to t
ig
hte
n
3
r
d
Stag
e
3
r
d
S
ta
g
e
2n
d
S
tage
1s1s
t
t
St
St
ag
ag
e
Us
Us
e
e
WrWr
W
W
W
en
en
c
h
UU
U
Us
s
ee

Apec Water Ultimate Series Specifications

General

Brand	Apec Water
Model	Ultimate Series
Category	Water System
Language	English