ENG
DESCRIPTION OF “GRANDE” ELECTRIC KETTLE DESIGN
1. LID LIFT BUTTON
2. ON/OFF SWITCH
3. HANDLE
4. ROTATING BASE
5. WATER LEVEL INDICATOR
6. WATER INLET/OUTLET
7. ANTI-SCALE FILTER
8. INDICATOR LIGHT
TECHNICAL DATA
The electric kettle “GRANDE”.
Model CZG-20-WHT, CZG-20-BK,
CZG-20-RED, CZG-20-GRAY
Voltage..........................230V~
Frequency.....................50Hz
Power............................2000W
Capacity........................2L
This appliance with the degree of protection against electric shock сlass I.
“NUMER PARTII” which is located on the rating plate of the product means the serial
number.
The present appliance is conformant with the European directive 2006/95/EC and
2004/108/WE.
INITIAL COMMENTS
• This kettle is intended for boiling water only.
• This kettle can only be connected to an earthed safety socket.
• The kettle is fit in the special base with a power cord, and can cooperate only with the original
(supplied) base. The base with a power cord should be exchanged or repaired by the
manufacturer in case of being damaged. Any modification or alteration will void the warranty
and create a potential safety hazard for the user.
• This kettle should be placed on even and stable surface. The power cord must not come in
contact with any hot kettle surfaces or other heat sources.
• Do not put your hands into the kettle when powered.
• Always boil as much water as necessary to save electricity.
• Always make sure that the kettle lid is closed. Never open the kettle during boiling.
• Do not allowed to fill the kettle with water above the mark MAX. The kettle always should be
filled with water above the mark MIN.
ATTENTION: If the kettle is overfilled the boiling water can jet.
ENG
• Do not keep water in the kettle for a period longer than one day. Water replacement is always
recommended.
• Special safety measures must be observed when using the kettle, particularly when pouring hot
water.
• Avoid contact with hot steam when pouring hot water.
• Small spots visible on the heater are the result of the action of water. The harder the water the
faster the scale build-up. Scale may adversely affect the operation of the kettle.
• Never put the kettle on metal trays or other metallic surfaces.
BEFORE FIRST USE
Prior to start the use, fill the electric kettle with water to a MAX level of a kettle capacity and then
add one spoon of baking soda. Boil water. Wait until water will cool and outpour it, fill the electric
kettle with water to a MAX level again and add one soup spoon of vinegar. Boil water. Wait until
water will cool. After these activities outpour water and thoroughly wash the electric kettle, boil
water and outpour again. The kettle is ready for use.
USING “GRANDE” ELECTRIC KETTLE
AUTOMATIC POWER CUT-OFF SYSTEM
The kettle is equipped with a system which prevents the kettle not filled with sufficient amount of
water from switching on. The Automatic Power Cut-Off System will switch the kettle off when the
heater becomes excessively hot.
If you have turned on the kettle without an adequate amount of water, turn off the kettle, fill it with
water to the max level and then wait about 10 minutes until it is completely cool before using it
again. After that time the Automatic Power Cut-Off System will be reset.
FILLING WITH WATER
It is necessary to take the kettle handle (3), then move upward from the rotary base (4) in the
vertical position and move in such position to the demanded place pouring the water into the kettle.
The kettle can be filled with water without lifting the lid, by pouring the water directly through water
inlet (6) or it can be filled with water by pressing the button to lift the lid (1). To this end press the
button (1) to lift the lid and fill the kettle with water. The kettle must not be plugged in if it is filled
below the „MIN” level visible in the water level indicator (5) or if it has been filled above the „MAX”
level mark of the water level indicator (5).
KETTLE CONNECTION TO THE SOURCE OF POWER
Put the kettle on the rotary base(4) after filling it with water, be sure, that the kettle properly fit in.
Then connect to the source of power and set the switch ON/OFF(2) up in the position "I".
SWITCHING THE KETTLE OFF
After water boiling the kettle automatically switch off and the switch ON/OFF (2) returns to the
position "0".
Wait at least 10 to 20 seconds before next use to allow the kettle to cool.
POURING WATER INTO DISHES
Take special precautions while pouring water into dishes after it has been boiled. Hold the kettle
by the handle (3), lift it off the rotating base (4) and carry it upright to the required place to pour the
water into dishes.
To Next Page
Loading...