Applied Biosystems Veriti

Questions and Answers

D
Desiree RiddleAug 18, 2025
What to do if printing fails on Applied Biosystems Veriti DC Drives?
- P
  phillipsmaryAug 18, 2025
  If printing fails on your Applied Biosystems DC Drives, there are several possible causes: * The printer might be incorrectly configured. Ensure the printer IP address on the instrument matches the IP address from the system administrator. * The printer may not be connected to the network. Check if the Ethernet cable is connected to the printer. * The instrument might not be connected to the network. Verify the Ethernet cable is connected to the instrument. * The Ethernet cable may be faulty. Try using a different Ethernet cable.
J
Joshua DunnAug 20, 2025
Why can't I see instruments in the “Select Instruments” screen when running Applied Biosystems Veriti DC Drives on multiple instruments?
- D
  Daniel ContrerasAug 21, 2025
  If you cannot see instruments in the 'Select Instruments' screen, when running on multiple instruments, there are several possible reasons: * The instruments may not be connected to the network. Ensure all Ethernet cables are connected to the instruments. * The network switch may be powered off. Check that all Ethernet cables are connected to the network switch. * A faulty Ethernet cable. Try a different Ethernet cable. * There might be an IP address conflict. Change the IP addresses on the instruments. * The 'Allow Remote Runs' setting in the Instrument Name screen may be set to 'No'. Change 'Allow Remote Runs' to 'Yes' in the Instrument Name screen.
S
stephensonmarkAug 23, 2025
What to do if sample tubes melt during run with Applied Biosystems DC Drives?
- J
  Jamie JohnsonAug 23, 2025
  If sample tubes melt during a run with Applied Biosystems DC Drives, consider the following: * You might be using incompatible consumables. Use only the recommended consumables. * The heated cover might be too hot. Run the Heated Cover Verification Test. * The sample block(s) might be too hot. Run the Heated Cover Verification Test.
D
Desiree Brown MDAug 26, 2025
What to do if there is no screen display when I power on my Applied Biosystems DC Drives instrument?
- S
  Stephanie MorrisAug 26, 2025
  If there is no screen display and no response when you power on the Applied Biosystems DC Drives instrument, there are a couple of things to check: * A blown fuse might be the issue. Check the fuses. * The instrument may not be properly connected to a power source. Ensure the power switch is on and the power cord is connected.
D
Darrell HolmesAug 28, 2025
What to do if the temperature does not match the specified temperature in Applied Biosystems Veriti DC Drives?
- J
  Jose SharpAug 28, 2025
  If the temperature does not match the specified temperature in your Applied Biosystems DC Drives, the instrument may require calibration. Run the Temperature Verification Test.
W
Wayne GarciaAug 30, 2025
How to fix a heated cover that is stuck on Applied Biosystems Veriti DC Drives?
- W
  Walter WilliamsAug 31, 2025
  If the heated cover is stuck on your Applied Biosystems DC Drives, the cam, platen, or cover assembly might be malfunctioning. Request service.
J
Jason HamiltonSep 2, 2025
What to do if the heated cover is not responsive on Applied Biosystems Veriti?
- H
  hayesloriSep 2, 2025
  If the heated cover is not responsive on your Applied Biosystems DC Drives, it may have failed. Run the Heated Cover Verification Test.
N
Nicole PearsonSep 4, 2025
Why is the cooling rate too slow on Applied Biosystems Veriti?
- Z
  Zachary OliverSep 5, 2025
  If the cooling rate is too slow on your Applied Biosystems DC Drives, it could be due to a Peltier assembly failure. Run the Cycle Performance Test.
D
Daisy WilkinsonSep 7, 2025
Why is the heating rate too slow on Applied Biosystems Veriti DC Drives?
- T
  Tonya BakerSep 7, 2025
  If the heating rate is too slow on your Applied Biosystems DC Drives, it could be due to Peltier failure. Run the Cycle Performance Test.
E
Eric PayneSep 9, 2025
Why is the cycling time too long on Applied Biosystems DC Drives?
- D
  Denise AguilarSep 9, 2025
  If the cycling time is too long on your Applied Biosystems DC Drives, it might be caused by a Peltier assembly failure. Run the Cycle Performance Test.