APS iBoard - User Manual

iBoard
®
Customer Support: info@iboardauto.com
Rev. 20210301
1
PART#: IB-R048
READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION. REMOVE CONTENTS
FROM BOX AND VERIFY ALL PARTS ARE PRE-
SENT. ASSISTANCE IS RECOMMENDED.
PART LIST
Front
iBoard
®
by APS
Fastener Size Tightening Torque (ft-lbs)
6mm 6-7
8mm 16-18
10mm 31-32
12mm 56-58
14mm 92-94
*ROCKER PANEL MOUNT
*DRILLING IS REQUIRED
Note: *(6) Support Brackets Are Universal
Driver/Passenger Front Mounting
Bracket (DFM/PFM)
Support Bracket
Driver/Passenger Center Mounting
Bracket (DCM/PCM)
Driver/Passenger Rear Mounting
Bracket (DRM/PRM)
DFS/PFS
Driver/Passenger
Front Support
Bracket (DFS/PFS)
Support Bracket
Support Bracket
Support Bracket
Support Bracket
Support Bracket

Summary

Step 1: Prepare Rocker Panel

Insert M8 Bolt Plates

Insert M8 Bolt Plates into the oval holes on the rocker panel as indicated.

Step 2: Assemble and Attach Front Mounting Bracket

Assemble Front Mounting Bracket

Assemble Driver Front Mounting Bracket and Front Support Bracket using specified hardware.

Mark and Drill Pinch Weld Holes

Mark and drill two holes on the pinch weld based on bracket position.

Step 3: Install Front Mounting Bracket

Secure Front Mounting Bracket

Install the assembled front mounting bracket onto rocker panel and pinch weld.

Step 4: Install Rear and Center Brackets

Repeat Bracket Installation

Repeat steps 1-3 for rear and center mounting brackets and support brackets.

Step 5: Mount Running Board

Attach Running Board to Brackets

Attach the running board to the mounting brackets using specified hardware.

Step 6: Final Tightening and Adjustment

Tighten All Hardware

Level and adjust the running board, then fully tighten all hardware per torque specs.

Step 7: Complete Installation

Install Second Side

Repeat steps 1-4 for the other side of the vehicle.

Periodic Inspection and Cleaning

Perform periodic inspections and use mild soap for cleaning.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Step 1: Initial Bracket Placement
5. Step 2: Assembling and Attaching Front Brackets
6. Step 3: Securing Front Brackets
7. Step 4: Installing Center and Rear Brackets
8. Step 5: Attaching Running Boards
9. Step 6: Final Tightening
10. Step 7: Completion
11. Maintenance Features

This document outlines the installation and maintenance instructions for the iBoard® by APS running boards, specifically model IB-R048. These running boards are designed to be mounted on the rocker panel of a vehicle and require drilling for installation.

Function Description:

The iBoard® running boards provide a sturdy step for easier entry and exit from a vehicle. They are designed to integrate with the vehicle's rocker panel, offering a secure and stable platform. The installation process involves attaching a series of mounting brackets to the vehicle's frame and pinch weld, onto which the running boards are then secured.

Important Technical Specifications:

The installation requires various fasteners with specific tightening torque values to ensure safety and stability. The provided table details these specifications:

• 6mm Fasteners: 6-7 ft-lbs
• 8mm Fasteners: 16-18 ft-lbs
• 10mm Fasteners: 31-32 ft-lbs
• 12mm Fasteners: 56-58 ft-lbs
• 14mm Fasteners: 92-94 ft-lbs

The kit includes a comprehensive list of components:

• Fasteners:
  • M8X30 Bolt Plate (X8)
  • M8X1.25-20mm Hex Bolt (X24)
  • M8 Flat Washer (X24)
  • M8 Hex Flange Nut (X32)
  • M6X1-20mm Square Head Bolt (X16)
  • M6 Large Flat Washer (X16)
  • M6 Nylon Lock Nut (X16)
• Brackets:
  • Driver/Passenger Front Support Bracket (DFS/PFS)
  • Driver/Passenger Front Mounting Bracket (DFM/PFM)
  • Driver/Passenger Center Mounting Bracket (DCM/PCM)
  • Driver/Passenger Rear Mounting Bracket (DRM/PRM)
  • Six universal Support Brackets

Usage Features:

The installation process is divided into several steps, starting from the driver's side and then repeating for the passenger's side.

Step 1: Initial Bracket Placement

• Locate eight mounting positions along the rocker panel.
• Insert four M8 Bolt Plates into the oval holes (specifically the 2nd, 4th, 6th, and 8th holes).

Step 2: Assembling and Attaching Front Brackets

• Assemble the Driver Front Mounting Bracket (DFM/PFM) and the Driver Front Support Bracket (DFS/PFS) using one M8X1.25-20mm Hex Bolt, two M8 Flat Washers, and one M8 Hex Flange Nut. Do not fully tighten these fasteners at this stage.
• Attach the assembled Driver Front Mounting Bracket to the rocker panel.
• Based on the position of the Driver Front Support Bracket, mark and drill two holes on the pinch weld.

Step 3: Securing Front Brackets

• Install the assembled Driver Front Mounting Bracket onto the rocker panel and pinch weld.
• Secure it with one M8 Bolt Plate, two M8X1.25-20mm Hex Bolts, five M8 Flat Washers, and three M8 Hex Flange Nuts. Again, do not fully tighten at this time.

Step 4: Installing Center and Rear Brackets

• Repeat Steps 1-3 for the remaining mounting positions on the driver's side (4th, 6th, and 8th holes). This involves installing two Driver Center Mounting Brackets (DCM/PCM), one Driver Rear Mounting Bracket (DRM/PRM), and three universal Support Brackets. All fasteners should remain loose at this stage.

Step 5: Attaching Running Boards

• Select a running board.
• Slip four M6x1-20mm Square Head Bolts into each bottom channel of the running board.
• Carefully position the running board onto the four mounting brackets. It is crucial not to slide the running board on the brackets to prevent damage to the board's bottom surface.
• Attach the running board to each mounting bracket using two M6x1-20mm Square Head Bolts, two M6 Large Flat Washers, and two M6 Nylon Lock Nuts. Do not fully tighten these fasteners yet.

Step 6: Final Tightening

• Level and adjust the running board to ensure proper alignment.
• Fully tighten all hardware according to the recommended tightening torques provided in the technical specifications table on page 1. It is important not to overtighten the nuts/bolts to prevent damage.

Step 7: Completion

• Repeat Steps 1-4 for the passenger side running board installation.
• The installation is then complete.

Maintenance Features:

• Periodic Inspections: Regular inspections are recommended to ensure all hardware remains secure and tight.
• Cleaning: To protect the running boards, use only mild soap and non-abrasive products for cleaning.

APS iBoard Specifications

General

Brand	APS
Model	iBoard
Category	Automobile Accessories
Language	English