EasyManua.ls Logo

AquaMaster AMS700 - User Manual

AquaMaster AMS700
36 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
M
M
O
O
D
D
E
E
L
L
S
S
A
A
M
M
S
S
7
7
0
0
0
0
,
,
A
A
M
M
S
S
9
9
0
0
0
0
,
,
A
A
N
N
D
D
A
A
M
M
S
S
9
9
5
5
0
0
O
O
W
W
N
N
E
E
R
R
’
’
S
S
M
M
A
A
N
N
U
U
A
A
L
L
A
A
N
N
D
D
I
I
N
N
S
S
T
T
A
A
L
L
L
L
A
A
T
T
I
I
O
O
N
N
G
G
U
U
I
I
D
D
E
E
V
V
E
E
R
R
S
S
I
I
O
O
N
N
2
2
.
.
0
0

Table of Contents

Questions and Answers

  • C
    craigbradleyAug 18, 2025
    What to do if AquaMaster AMS700 no soft water?
    • C
      Chloe WilliamsAug 18, 2025
      If your AquaMaster Water Filtration Systems is not providing soft water, here are a few things to check: * First, make sure that the bypass valve is in the Service position. * Confirm that the appliance is plumbed correctly. * If there has been an extended power outage, reset the time of day. * If the water hardness has increased, re-test the water and enter a new setting number. * Also, check if the appliance is metering water. Flow should be indicated with water usage. If there is no flow, further inspection is needed.
  • R
    Robert WebbAug 21, 2025
    Why AquaMaster AMS700 flow indicated when water is not being used?
    • T
      Tracie JohnstonAug 22, 2025
      If your AquaMaster Water Filtration Systems is showing flow even when water is not being used, it's likely that the household plumbing system has a leak. You should repair the leak to resolve this issue.
  • A
    Aaron MorganAug 26, 2025
    What to do if AquaMaster Water Filtration Systems no flow is indicated when water is flowing?
    • J
      John ParkerAug 26, 2025
      If your AquaMaster Water Filtration Systems is not indicating flow when water is flowing, consider these potential causes: * Ensure the bypass valve is in the Service position. * Verify the appliance is plumbed correctly. * Check if the sensor is receiving a signal from the magnet on the turbine. Remove the sensor from the bypass housing and test it with a magnet on either flat side. If flow is indicated, check the turbine. If no flow, replace the sensor.
  • S
    Sherry BartonAug 28, 2025
    Why AquaMaster AMS700 appliance stays in regeneration?
    • W
      Wendy SchultzAug 28, 2025
      If your AquaMaster Water Filtration Systems appliance remains in regeneration, consider the following: * Ensure the controller is fully pushed onto the drive end cap. * Replace the magnet disk if it is defective. * Remove any foreign objects from the valve body. * If the valve assembly is broken and the motor is running, repair the drive end cap.
  • N
    Nathan Marquez IISep 1, 2025
    Why AquaMaster Water Filtration Systems not regenerating in proper sequence?
    • J
      Jason PadillaSep 1, 2025
      If your AquaMaster Water Filtration Systems is not regenerating in the proper sequence, it could be due to a defective magnet disk or a defective controller. Try replacing the magnet disk first. If that doesn't solve the issue, replace the controller.
  • D
    david52Sep 4, 2025
    What to do if AquaMaster Water Filtration Systems has excess water in brine cabinet?
    • C
      Carrie RussellSep 4, 2025
      If you observe excess water in the brine cabinet of your AquaMaster Water Filtration Systems, here's what you can do: * Check for and remove any restrictions, thaws, or straighten the drain line if it's frozen or pinched. * Clean the flow control, air check/draw tube, and brine line. Also, remove any sediment from the brine cabinet. * Clean or replace the injector assembly, and replace the throat if it was removed. * If the brine refill valve is sticking, remove the valve and check for any obstructions.
  • S
    Steve MoranSep 12, 2025
    What to do if AquaMaster AMS700 no read-out in display?
    • L
      Larry MitchellSep 12, 2025
      If there is no read-out in display of your AquaMaster Water Filtration Systems, here are the possible solutions: * Ensure the electric cord is plugged in. * Check the power source and ensure the outlet is not controlled by a switch. * Test the transformer with a volt meter for 12 VAC at the control. If it's less than 10 VAC or greater than 14 VAC, replace the transformer. * If there is 12 VAC present at the controller, replace the controller, as the circuit board may be defective. * If the ambient room temperature is too high (exceeds 120°F), the display will blank out. No action is necessary, as this does not affect the operation of the controller.
  • C
    Cheryl MontgomeryNov 14, 2025
    Why AquaMaster AMS700 no soft water after regeneration?
    • M
      mary74Nov 14, 2025
      If you find that you're not getting soft water after regeneration with your AquaMaster Water Filtration Systems, there could be several reasons: * First, ensure that there is enough salt in the brine cabinet. Add salt if needed. * Next, check for sediment in the brine cabinet that may have plugged the brine line and air check/draw tube. Flush the air check/draw tube with clean water, clean the injector assembly, and remove any sediment from the brine cabinet. * Also, a salt bridge may have formed due to high humidity or the wrong kind of salt. Test with a blunt object like a broom handle to dislodge it, or use hot water around the inside perimeter to loosen the salt. * Check if the flow control is plugged. If so, remove the brine piston housing and clear any debris from the flow c...

AquaMaster AMS700 Specifications

General IconGeneral
BrandAquaMaster
ModelAMS700
CategoryWater Filtration Systems
LanguageEnglish