What to do if my Aquatek Water Filtration System is leaking?
If your Aquatek Water Filtration System is leaking, first check if the fittings are loose and tighten them. If the tank is cracked, bypass the unit. If the drain line or hose is damaged, replace it.
Why is there reduced water flow in my Aquatek Water Filtration System?
If you experience reduced water flow or pressure in your Aquatek Water Filtration System, it may be due to the breakdown of the media. In this case, bypass the unit and replace the media. Contact us to replace media - 877-414-PURE
How to fix Aquatek ATAIOIF Water Filtration Systems timer not displaying time?
If the timer on your Aquatek Water Filtration System does not display the time of day, check the following: * Ensure the transformer is plugged in to connect power. * Verify there is electrical power at the outlet; repair or use a working outlet if necessary. * If the above steps don't work, the transformer or PC board may be defective and require replacement.
Why is Aquatek Water Filtration Systems timer displaying the wrong time?
If the timer on your Aquatek Water Filtration System isn't showing the correct time, it might be due to a switched outlet. Use an uninterrupted outlet. Also, a power outage could be the reason, so reset the time of day. If neither of these fixes the issue, the PC board may be defective and need replacing.
How to adjust backwash time on Aquatek ATAIOIF control valve?
If the control valve on your Aquatek Water Filtration System backwashes at the wrong time, the time of day may not be set correctly, so reset it. Also, the backwash time may be set incorrectly; reset that as well. If there was a power outage, reset the valve to the correct time of day.
What to do if Aquatek Water Filtration Systems control valve is stuck in backwash?
If the control valve is stalled in the backwash on your Aquatek Water Filtration System, several issues could be the cause. The motor may not be operating, in which case it should be replaced. Ensure there is electrical power at the outlet; repair or use a working outlet if needed. Other potential causes include a defective transformer or PC board (replace as necessary), a broken piston retainer (replace the drive cap assembly), a broken main or regenerant piston (replace the piston), or a broken drive gear or drive cap assembly (replace the gear or assembly).
Why doesn't my Aquatek ATAIOIF backwash when holding REGEN?
If the control valve on your Aquatek Water Filtration System doesn't automatically backwash when you press and hold the REGEN button, ensure the transformer is connected. Also, check for power at the outlet and repair or use a working outlet if necessary. If these aren't the problem, the drive gear or drive cap assembly could be broken, or the PC board may be defective, requiring replacement of the affected part.
Why Aquatek Water Filtration Systems only backwashes when REGEN is pressed?
If your Aquatek Water Filtration System's control valve only backwashes when the REGEN button is held down, but not automatically, the PC board may be defective and needs to be replaced. Alternatively, there could be a set-up error, so check the control valve set-up procedure.
What does Err 1002 mean on Aquatek Water Filtration Systems?
If your Aquatek Water Filtration System displays Err - 1002, indicating the control valve motor ran too short, it could be due to a few reasons. Foreign material might be lodged in the control valve, so open it up and inspect the piston assembly and Seal and Spacer Stack Assembly. There could also be mechanical binding; check the Piston and Seal and Spacer Stack Assembly, Reduction Gears, Drive Bracket, and Main Drive Gear Interface. The Main Drive Gear might be too tight, so loosen it. Finally, improper voltage to the Circuit Board could be the cause; verify the proper voltage is being supplied. After these steps, press NEXT and REGEN buttons at the same time for 3 seconds to resynchronize software with piston.
What does Err 1001 mean on Aquatek Water Filtration Systems?
If your Aquatek Water Filtration System displays 'Err - 1001', it means the control is unable to sense motor movement. This could be because the motor isn't fully inserted, motor wires are broken, or disconnected. Disconnect power, ensure the motor is fully engaged, check for broken wires, and ensure the two-pin connector on the motor is connected to the two-pin connection on the Circuit Board labeled MOTOR. It could also be that the Circuit Board is not properly snapped into the drive bracket, so ensure it is properly snapped in. Another cause could be missing reduction gears, so replace them if needed. After these steps, press NEXT and REGEN buttons at the same time for 3 seconds to resynchronize software with piston.
Details technical parameters like water pressure, temperature, and flow rates for the ATAIOIF system.
Specifies the power supply voltage, frequency, output voltage, and current for the unit.
Outlines the pipe size, accuracy, and minimum flow rate requirements for the integrated water meter.
Lists important warnings regarding lubricants, water quality, electrical hazards, and proper installation.
Emphasizes the importance of reading the manual for proper operation and maintenance of the filter.
Provides background information on Zeolite as a filter media, its discovery, and properties.
Describes the characteristics, classification, and GRAS status of Zeolite filter granules.
Explains how the sulfur and iron filter works using oxidation, filtration, and backwashing cycles.
Details the control valve's primary operations: Pre-Treatment Oxidation, Service/Filtration, and Backwash.
Explains the mineral tank's function in holding the filtration media for water treatment stages.
Lists essential items and conditions like power, drain, and temperature limits before starting installation.
Covers floor space prep, leveling, connection kit, plumbing preparations, and initial connections.
Guides drain line connection, specs, air gap, and critical precautions for installation.
Instructions for loading the filter media into the tank, including distributor tube placement.
Steps to put the unit into operation after filling, including flushing and valve connection.
Process to reduce pressure within the unit before performing maintenance or media replacement.
Guides on how to remove the control valve and empty the tank of existing filter media.
Step-by-step guide for initiating the system, including bypass, flushing, and regeneration.
Introduces the Aquatek ATAIOIF Iron Filter Control Valve for programming and operation.
Step-by-step guide to set the current hour and minute display on the unit's control valve.
Explains how to initiate manual regeneration and the total duration of the cycle.
Explains how bypassing reroutes unfiltered water and when it is necessary for service or emergencies.
Provides instructions on how to turn the bypass valve handles to activate bypass mode.
Addresses problems like timer not displaying, incorrect time, and unit leaking with possible solutions.
Solutions for reduced water flow or pressure, including media issues and bypass recommendations.
Troubleshooting for control valve issues like stalling in backwash or not automatically backwashing.
Resolves error codes related to motor movement, cycle position, and timing issues.
Details the five-year warranty for defects in material and workmanship under normal use.
Lists conditions like misuse, accident, or acts of God that are not covered by the warranty.
Provides contact information and procedures for obtaining warranty service and support.
General| Brand | Aquatek |
|---|---|
| Model | ATAIOIF Series |
| Category | Water Filtration Systems |
| Language | English |
To Next Page
