AQUATROL POWERFLO Series

Other manuals for AQUATROL POWERFLO Series

Service Manual28 pages

Questions and Answers

A
Anthony HoganSep 10, 2025
Why is there excessive water in the brine tank of my AQUATROL Control Unit?
- R
  Ricky BeltranSep 10, 2025
  Excessive water in the brine tank of your AQUATROL Control Unit can be caused by a plugged drain line flow control (clean the flow control), a plugged injector system (clean the injector and screen), the timer not cycling (replace the timer), foreign material in the brine valve (replace the brine valve seat and clean the valve), or foreign material in the brine line flow control (clean the brine line flow control).
A
Anthony CobbAug 23, 2025
Why is my AQUATROL POWERFLO softener failing to brine draw?
- Y
  yolanda01Aug 23, 2025
  If your AQUATROL Control Unit softener isn't drawing brine, several issues could be the cause. Check for a plugged drain line and clean the flow control. A plugged injector could also be the problem, so clean or replace the injector and screen. Ensure there's water in the brine tank and check for restrictions in the B.L.FC, making sure the safety float isn't stuck. Low water pressure can also prevent brine draw, so increase water pressure. Additionally, check the brine line for air leaks, and inspect the seal, spacer, and piston for scratches and dents, as an internal control leak could be the cause.
N
njenkinsAug 25, 2025
How to fix loss of water pressure in AQUATROL Control Unit?
- A
  adam57Aug 25, 2025
  To fix a loss of water pressure in your AQUATROL Control Unit, start by checking for fouling of the inlet pipe and clean or replace the pipeline if necessary. Also, inspect the resin for fouling and clean it, pretreating to prevent future issues. Lastly, ensure proper backwash by resetting the flow rate and time of backwash to address too many resin fines.
J
jose63Aug 26, 2025
What causes poor water quality in AQUATROL Control Unit and how to resolve it?
- M
  Michael MorrisonAug 27, 2025
  Poor water quality in your AQUATROL Control Unit can stem from several issues. First, check the items listed in Correction # 3. Ensure the bypass is closed. Also, check for channeling, ensuring that the service flow isn't too slow or too high.
R
Ryan CunninghamAug 27, 2025
What to do if AQUATROL POWERFLO fails to regenerate automatically?
- M
  Mrs. Jennifer Johnson DVMAug 28, 2025
  If your AQUATROL Control Unit fails to regenerate automatically, first check if the meter cable is disconnected and reconnect it if necessary. If the transformer is damaged, replace it. If the electronic controller or sensor is damaged, consider replacing or repairing it.
T
timothyjohnsonAug 29, 2025
Why AQUATROL Control Unit regeneration at wrong time and how to fix it?
- N
  Natasha GardnerAug 29, 2025
  If your AQUATROL Control Unit is regenerating at the wrong time, it's likely due to the timer being improperly set, possibly due to a power failure. Reset the timer to resolve this issue.
M
Mrs. Danielle HendersonSep 18, 2025
Why is my AQUATROL Control Unit losing mineral through the drain line?
- P
  penny56Sep 18, 2025
  Loss of mineral through the drain line in your AQUATROL Control Unit can be caused by air in the water system. Ensure that the well system has a proper air eliminator control and check for dry well conditions. It can also be due to an improper size drain line flow control; check for the proper drain rate.
E
Erin MendozaSep 22, 2025
Why is there iron in the conditioned water from my AQUATROL Control Unit?
- S
  Steven EllisSep 22, 2025
  Iron in the conditioned water from your AQUATROL Control Unit is likely due to a fouled mineral bed. Check the backwash, brine draw, and brine tank fill. Increase the frequency of regeneration and the backwash time.
J
Jonathan BakerSep 8, 2025
How to fix an AQUATROL Control Unit that fails to regenerate?
- M
  Matthew RussellSep 8, 2025
  If your AQUATROL Control Unit fails to regenerate, it could be due to a few reasons. First, check that the unit has permanent electrical service by checking the fuse, plug, pull chain, or switch. Second, the timer might be defective and need replacing. Third, a power failure may have occurred, so reset the time of day.
U
uburnettSep 4, 2025
Why does my AQUATROL POWERFLO Control Unit cycle continuously?
- S
  sarah36Sep 4, 2025
  If your AQUATROL Control Unit cycles continuously, it is probably due to a faulty timer. Replace timer.