Aquavista 21-K822-AVD User Manual

1
HIGH-ARC KITCHEN FAUCET WITH
OPTIONAL SIDE SPRAY
21-K822-AVD – Polished chrome finish
21-K822- AV-BND – Brushed nickel finish
PACKAGE AND HARDWARE CONTENTS
AD
NSF/ANSI 61
A
PART DESCRIPTION
QUANTITY
C
D
A
B
E
F
G
A Faucet body
1
B Hose connection cap
1
C Side spray assembly
1
D Side spray support
1
E Side spray mounting nut
1
F Mounting nut
2
G Putty plate
1
SAFETY INFORMATION
Please read and understand this entire manual before attempting to
assemble, operate or install the product.
WARNING
• Protect your eyes with safety glasses when cutting or soldering water supply
lines.
CAUTION
• If you solder the joints during installation, the seats, cartridges, and washers
must be removed before using a flame or the warranty will be voided on
these parts.
• Cover the drain to avoid losing parts.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package and hardware contents list. If any part is missing or damaged, do
not attempt to assemble the product. Contact customer service for replacement
parts.
Estimated Assembly Time: 30 minutes
Tools required for assembly (not included): adjustable wrenches, groove joint
pliers, pipe wrench, Phillips screwdriver, supply lines, thread seal tape, silicone.
Installation may vary depending on how the previous faucet was installed.
Supplies necessary for the installation of the faucet are not all included;
however, they are available wherever plumbing supplies are sold.
Prior to beginning installation, turn off the hot and cold water lines, then turn
on the old faucet to release built-up pressure. When installing the new faucet,
hand tighten the connector nuts. DO NOT OVERTIGHTEN. Connections
that are too tight will reduce the integrity of the system.
Need Help? Please call our toll-free line at (877) 319-3757 (7:30 a.m. to 4:30 p.m. CST) for additional assistance or service.
11-25-2019Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • HomewerksWW.com

Aquavista 21-K822-AVD Specifications

General

Brand	Aquavista
Model	21-K822-AVD
Category	Kitchen & Bath Fixtures
Language	English

Summary

Package and Hardware Contents

Safety Information

Warning

Protect eyes with safety glasses when cutting or soldering water supply lines.

Caution

If soldering joints, remove seats, cartridges, and washers before using flame; warranty void.

Preparation

Tools Required for Assembly

Lists tools needed for assembly: adjustable wrenches, groove joint pliers, pipe wrench, Phillips screwdriver, supply lines, thread seal tape, silicone.

Estimated Assembly Time

Indicates an estimated assembly time of 30 minutes.

Product Specifications

Max Flow Rate

Specifies maximum flow rate of 1.8 GPM (6,81LPM) at 60 PSI.

Certifications

Lists ASME A112.18.1/CSA B125 and NSF 61-9 certifications.

Finish Options

Describes available finishes: polished chrome or brushed nickel.

Ceramic Cartridge Details

Details ceramic cartridges' lead content for wetted surfaces.

Total Weight

States the total weight of the item is 2.05 lbs.

Assembly Instructions

Step 1: Prepare for Installation

Turn off water, disconnect old faucet, and clean mounting surface.

Step 2: Mount Faucet Body

Apply sealant, position faucet shanks, and thread mounting nuts by hand.

Step 3: Install Side Spray Support

Insert side spray support through sink hole and thread mounting nut.

Step 4: Connect Side Spray Hose

Attach side spray hose to faucet connection and tighten.

Step 5: Connect Water Supply Lines

Wrap thread seal tape on faucet shanks and hand tighten supply lines.

Step 6: Flush and Check for Leaks

Remove aerator, turn on water, flush debris, and check connections for leaks.

Operating Instructions

Handle Operation

Lever handles control hot/cold water flow; rotate forward for water, adjust opening for volume.

Stopping Water Flow

Returning handles to the original position stops the water flow.

Care and Maintenance

Cleaning Recommendations

Clean periodically with a soft cloth; avoid abrasive cleaners, steel wool, and harsh chemicals.

Troubleshooting

Faucet Leaks Underneath Handle

Addresses leaks under the handle due to loose bonnet or O-ring issues.

Water Not Shutting Off Completely

Solves issues with rubber valve seats being dirty, stuck, or broken.

Faucet Leaks Around Aerator

Fixes leaks around the aerator due to improper fitting or dirt.

Improper Water Pattern

Corrects improper water patterns caused by dirty or misassembled aerators.

Replacement Parts

Limited Lifetime Warranty