elephantrunk
TM
1
Place your elephantrunk at the desired location with
the help of another person.
The courier must be able to freely access your elephantrunk to make deliveries.
Choose a protective location, such as on a porch or under an eave, and away from sprinklers.
You can anchor your elephantrunk to a hardscaped or wooden surface. It will require drilling a hole into the surface, so make sure you
pick the right location.
parcel drop
2
Open the bottom
door and mark the
ground through the
hole in the floor.
4
Drill a hole where you marked the ground:
For hardscape (for example, stone walkway or
concrete pad), drill a hole 2.5” deep at the mark with
a 5/8” masonry bit.
For wood (for example, deck or porch), drill a pilot
hole 2” deep at the mark using a 1/4” wood bit.
2.5” for lag shield
2.0” for wood
5/8” hole 1/4” hole
Hardware and Parts (included) Tools (not included)
x 1, mounting bolt
x 1, lag shield
(for hardscape
installation only)
x 1, washer
x 1, placard
elephantrunk
TM
This address is equipped with an
parcel drop
location:
www.architecturalmailboxes.com © Architectural Mailboxes, LLC, 2012. Rev I
x 1, handle
x 1, cushion
x 4, placard screws
x 2, handle screws
Phillips head screwdriver
- or -
Hex wrench
1/4” wood drill bit
(if installing on wood deck/porch)
5/8” masonry drill bit
(if installing on hardscape)
Drill suitable for drilling into masonry or wood
x 2, keys x 1, mounting knob
elephantrunk installation
Carefully unpack the elephantrunk, parts and hardware.
Choose where to locate your elephantrunk
3
After marking the ground, place the elephantrunk
aside before continuing.
7
With help, lift the elephantrunk over the installed bolt,
aligning the bolt through the hole in the floor. DO NOT
secure in place with the mounting knob yet.
8
Level the elephantrunk by adjusting the feet up
and down.
9
Place the washer over the bolt and screw on the
mounting knob. The knob only needs to be hand
tightened.
10
Place the cushion onto the floor over the mounting
knob.
11
Open the top door and attach the handle with the two
handle screws.
To activate your warranty, register your product at:
www.architecturalmailboxes.com/registration
4
2
Write the location of your elephantrunk onto the
placard with a permanent marker.
3
Attach the placard to your front entry in a conspicuous
location so the courier knows where to deliver your
items.
5
For hardscape:
Remove any debris
from the hole and insert
the lag shield so it is
flush with the surface.
Screw the mounting bolt
into the lag shield.
For wood:
Screw the
mounting bolt
directly into the
surface.
Use the hex portion at the
center of the bolt to screw
it into the hole.
For both installations,
screw it all the way so the
hex portion is touching
the surface.
x 1, outgoing partition
6
Carefully screw the four
leveling feet into the bottom
of each leg about half way.
x4
elephantrunk use
placard installation
Incoming drum can accept parcels up to
11.5” x 7.3” x 9.3”.
© 2012, Architectural Mailboxes, LLC Rev. A
Slide the outgoing
partition into the grooves
to trap your outgoing
parcel for future pickup.
Swing down the “No Deliveries”
indicator to suspend deliveries.
Retrieve your parcels by unlocking the bottom door.
NOTE: The elephantrunk parcel drop is NOT intended to replace a mailbox. Its primary
purpose is to receive parcel deliveries.
Over tightening with a tool may damage
the floor and invalidate your warranty.
R
by
Give us a call at (800) 464-7491 or email
et-help@architecturalmailboxes.com with any questions.
We’re all ears!
x 4, leveling feet
1
Remove protective plastic coating from the placard.
To Next Page
Need help?
General