How to prevent rapid or uneven tire wear on my Arctic Cat VLX 70002017?
Rapid or uneven tire wear on your Arctic Cat Offroad Vehicle can be caused by worn or loose wheel hub bearings, incorrect front wheel alignment, or incorrect tire inflation pressure. Replacing the bearings, adjusting the alignment, and adjusting the tire pressure can help resolve this issue.
Why is my Arctic Cat VLX 70002017 steering oscillating?
Steering oscillation in your Arctic Cat Offroad Vehicle can occur due to several reasons. The tires might be inflated unequally, wheels could be wobbly, or the wheel hub cap screws might be loose or missing. Also, check for worn or damaged wheel hub bearings, worn or loose tie rod ends, defective or incorrect tires, damaged A-arm bushings, or loose bolts and nuts on the frame. To resolve this, adjust the tire pressure, replace the wheels, tighten or replace the cap screws, replace the wheel hub bearing, replace or tighten the tie rod ends, replace the tires, replace the bushings, or tighten the bolts and nuts.
Why is my Arctic Cat VLX 70002017 steering pulling to one side?
If your Arctic Cat Offroad Vehicle's steering pulls to one side, it could be due to several factors: unequally inflated tires, incorrect front wheel alignment, worn or broken wheel hub bearings, a distorted frame, or a defective shock absorber. Try adjusting the tire pressure, adjusting the front wheel alignment, or replacing the wheel bearings, shock absorber, or repairing/replacing the frame.
How to fix heavy or stiff handling on my Arctic Cat VLX 70002017?
Heavy or stiff handling on your Arctic Cat Offroad Vehicle may result from several issues: incorrect front wheel alignment, inadequate lubrication, low tire inflation pressure, tie rod ends seizing, or linkage connections seizing. Try adjusting the alignment and pressure, lubricating the appropriate components, replacing the tie rod ends, or repairing/replacing the connections.
What to do if my Arctic Cat VLX 70002017 has steering noise?
Steering noise in your Arctic Cat Offroad Vehicle could be due to loose cap screws or nuts, broken or damaged wheel hub bearings, or inadequate lubrication. Make sure to tighten the cap screws and nuts, replace the bearings, and lubricate the appropriate components.
General| Brand | Arctic Cat |
|---|---|
| Model | VLX 70002017 |
| Category | Offroad Vehicle |
| Language | English |
Instructions for preparing the ATV for storage to prevent damage and deterioration.
Procedures for correctly preparing the ATV after it has been stored.
Detailed procedure for changing the engine/transmission oil and filter.
Procedure for checking and changing lubricant in front differential and rear drive.
Procedures for checking brake fluid level and bleeding the hydraulic brake system.
Procedure for checking brake pad thickness and replacing worn pads.
Procedure for checking and adjusting front wheel alignment.
Troubleshooting steps for engine starting, stalling, noise, and power loss.
Detailed steps for removing the engine and transmission from the ATV frame.
Procedures for separating and disassembling the crankcase halves.
Steps for installing the engine/transmission into the ATV frame.
Procedures for checking, filling, and servicing the cooling system.
Procedures for cleaning, maintaining, and charging the ATV battery.
How to test the regulator/rectifier output voltage.
Procedures for testing and replacing starter motor and starter relay.
Explanation of indicator lights and retrieving diagnostic trouble codes (DTCs).
Troubleshooting steps for spark issues, battery charging, and starter problems.
Troubleshooting steps for problems with power not transmitting to wheels.
Troubleshooting steps for poor braking, excessive lever travel, and fluid leaks.
Steps to remove the front differential assembly, including axles and knuckles.
Procedures for disassembling and assembling the input shaft.
Steps for disassembling and assembling the differential assembly.
Steps for disassembling and assembling the pinion gear.
Procedures for adjusting differential backlash and ring gear end-play.
Steps to remove and disassemble the rear drive axle.
Steps to remove, disassemble, clean, inspect, assemble, and install brake caliper.
Troubleshooting for rear wheel oscillation and vehicle pulling/erratic steering.
To Next Page