This document serves as the user's manual for the AREBOS Solar Heating system, specifically models AR-HE-SH300(T). It provides comprehensive instructions for safe installation, operation, maintenance, and disposal of the solar heating unit.
Function Description:
The AREBOS Solar Heating system is designed to heat pool water using solar energy. It utilizes solar collectors to absorb sunlight, transferring the heat to the pool water as it circulates through the system. The primary function is to raise and maintain pool water temperatures, offering an environmentally friendly and cost-effective method for pool heating by eliminating fuel costs. The system is designed to work in conjunction with an existing pool pump, which automatically circulates water through the solar collectors. Heated water is then returned to the pool through the return lines. The manual emphasizes that the system should only circulate water when the sun is shining to maximize efficiency and prevent cooling the pool water.
Important Technical Specifications:
The manual lists the product name as "Solar heating" and the model number as AR-HE-SH300(T).
Art. Nr.:
- 4260627425884 (single set)
- 4260627425891 (double set)
Measurements:
- Single set: 66cm x 300cm
- Double set: 2 x 66cm x 300cm
The system is designed for use with pool pumps. For pumps greater than 0.5HP (approximately 370W), a diverter kit is required to shunt flow, which is crucial for the product's longevity. The manual includes detailed fastener lists for both single and double sets, specifying components like O-rings, 1-1/2" S.S. Clamps, Small Elbows, and Big Elbows. The diverter kit includes a 3-Way Valve, 1.5" Threaded Check Valve, 1.5" Threaded Tee, 1.5" Threaded Male Connector, 1.5" Threaded female Connector, and O-Rings.
Usage Features:
The AREBOS Solar Heating system is designed for straightforward use, aiming to heat pool water up to 38°C during sunny periods.
- Installation Flexibility: Collectors can be installed in any location that receives at least 6 hours of full sun daily. For angled installations (e.g., on a roof or rack), collectors should face a southerly direction for optimal performance.
- System Layouts: The manual provides detailed diagrams for single and double set configurations, as well as a setup with a diverter kit.
- Single Set: Illustrates the basic connection of one solar heating unit to the pool's circulation system, showing the flow of water from the pump through the collector and back to the pool.
- Double Set: Explains how to connect two solar heating units, particularly for systems using pumps of 0.5HP or less. It emphasizes the correct placement of baffles for efficient circulation.
- Diverter Kit Setup: Essential for pumps greater than 0.5HP (ca. 370W), this setup shunts excess flow to prevent damage to the product and maintain optimal performance.
- Connection Process: The manual outlines a step-by-step connection process:
- Remove the protection cap.
- Insert the O-ring into the male ending (using silicon lubricant).
- Insert the male end into the female end (matching the slot).
- Turn and fix the main pipe.
This process is applicable for both standard and baffled connections.
- Optimal Operation: To maximize heating, water should be circulated through the solar collectors for at least 6 hours per day during daylight hours on sunny days. The collectors should feel cool to the touch when operating correctly, indicating heat transfer to the water. The water returning to the pool should be 3-5 degrees warmer than the pool itself.
- Automated Control (Optional): An automatic controller can be integrated to sense water temperature and available solar radiation, automatically directing water flow via a 3-Way Valve, ensuring efficient heating and preventing cooling during cloudy or chilly periods.
Maintenance Features:
Proper maintenance is crucial for the longevity and efficient operation of the AREBOS Solar Heating system.
- Winterization: This is a critical annual maintenance step to prevent freeze damage.
- The entire solar system, including collectors, must be drained completely, similar to other pool equipment.
- Remove the vacuum relief valve at the top of the solar system.
- Remove the rubber end cap at the bottom.
- Ensure all water is drained from the system.
- Replace end caps and blow compressed air in the reverse direction of normal water flow for thorough draining.
- Storing solar collectors in a warm, dry place during winter is highly recommended.
- Troubleshooting Leaks:
- The collectors are warranted against defects in materials and workmanship.
- Leaks due to other reasons (e.g., freeze damage, which is not covered by warranty) can be repaired on-site.
- Solar Collector Repair Method:
- Locate the leaking tube.
- Carefully cut away approximately 1 inch of the tube at both headers using a sharp utility knife.
- Drive a 3/16" sheet metal screw (preferably stainless, 1/2" to 3/4" long) into the hole in the header. Avoid overtightening.
- If the screw strips or the repair leaks, use a bigger screw or wrap nylon tape around the screw for sealing.
- It is also advised to check the circulation system, specifically the placement of baffled and non-baffled spots, if a collector develops a leak.
- General Care: The manual implies that with proper care and winterization, the solar collectors will provide many years of service.
Safety and Disposal:
- Safety Warnings: Users are instructed to read the manual thoroughly, observe all safety information, warnings, and cautions to prevent personal injury or property damage.
- The product must not be disposed of with household waste.
- Warning: Hot surface! Do not step on the heater to avoid burns.
- Warning: Read safety instructions carefully to avoid serious injury or damage.
- Installation on roofs requires familiarity with roof work, proper ladders, and safety equipment; otherwise, professional installation is recommended.
- Ground installations should ensure rack supports do not provide children access to the pool.
- Disposal Instructions:
- Packaging: Dispose of packaging according to regional guidelines. Plastic bags should be kept out of reach of children to prevent suffocation.
- Waste Equipment: Equipment must be disposed of in accordance with local waste disposal rules. At the end of its life, valuable raw materials should be recycled. Local waste disposal companies or recycling centers can assist.
- "Dustbin" Symbol: This symbol indicates that electrical appliances do not belong in household waste. Users should utilize designated collection points for electrical and electronic equipment to ensure proper disposal, prevent environmental harm, and protect human health.
The manual concludes with imprint information, including the manufacturer's details, customer service number, and VAT identification number.
Need help?
General
To Next Page