Aritech IU2080 - User Manual

[part number] © 2001 Interlogix BV
All rights reserved
N
I
NSTALLASJON
EST
S
IGNALISATSIOONIAHELA KONTROLLER.
PAIGALDUS- JA HOOLDUSJUHEND.
S
I
NSTALLATIONS- OCH SERVICEHANDLEDNING
LT
S
IGNALIZATORIŲ KONTROLĖS MODULIS.
ĮRENGIMO IR APTARNAVIMO INSTRUKCIJA.
DK
I
NSTALLATIONSVEJLEDNING
LV
I
NDIKĀCIJAS ĶĒDES KONTROLLERS.
UZSTĀDĪŠANAS INSTRUKCIJA.
Installation Instructions
GENERAL DESCRIPTION
The IU2080 provides an interface between the two wire multiplexed ring circuit and local
supply sounders and strobes with their associated user external power supply (24 V).
The external power supply provides the power to drive the sounders and strobes. A
number of devices totalling up to 3 A can be connected to the sounder spur (750 mA in
applications requiring AFNOR approvals).
The ICC monitors the local power supply for a low voltage condition and the external
fault relay contacts (via fault + -ve) for an open condition. An end-of-line (EOL) resistor
is used to insure that the local supply loop is intact. The ICC monitors for loop shorts as
well as for loop open circuits via this resistor. Moreover, the ICC can provide a means
for EOL monitoring via a Z-style connection back to the ICC itself.
INDICATORS
The IU2080 contains a red LED that will light when the relay is in a position to cause the
sounders and sirens to be energized. The green LED indicates that the external power
supply voltage is present and greater than approximately 8 V.
INSTALLATION
Please refer to the wiring diagrams for the proper wiring of the indicating circuit
controller.
S
ETTING THE ADDRESS
Use a screwdriver to adjust the two rotary switches on the unit. Set the left rotary switch
(MSB: 0-12) for the 10’s and 100’s digit, and the right rotary switch (LSB) for the 0-9
digit. Do not set the address to either 0 or 129. This will not produce a response from
the unit.
TECHNICAL DATA
Operating voltage...................................................................................................17-28 V
(at the communication loop terminals)
Total standby current ...........................................................................................< 350 µA
(< 200 µA typical)
Maximum loop alarm current ...............................................................................< 3.5 mA
End of line resistor value..............................................................................10 k ¼ W, 5%
Bell loop impedances at 24 V:
Short circuit.......................................................................................................< 3.3 k
Quiescent ..............................................................................................3.3 k – 13.0 k
Open circuit ....................................................................................................< 13.0 k
Local power supply, low voltage detection:
24 V supply....................................................................................................< 20.4 V
Local supply current (standby) .........................................................< 11.0 mA @ 24 VDC
Local supply current (alarm).............................................................< 72.0 mA @ 24 VDC
plus bell loop load current
Supervisory voltage....................................................................approx. 2.2 VDC inverted
Fuse rating....................................................................................................................3 A
GB
2000 Series ICC Module IU2080
Indicating Circuit Controller
WWW.UKPANELS.COM

Summary

Installation Instructions

General Description

Overview of the IU2080 module's interface and functionality with sounders and strobes.

Indicators

Explanation of the red and green LEDs on the IU2080 module and their meaning.

Installation

Guidance on referring to wiring diagrams for proper installation of the circuit controller.

Wiring Diagrams and Configurations

Style Y and Z Operation

Wiring configurations for Style Y and Style Z operation with and without power supply trouble relay.

Component Identification

Identification of key components used in wiring diagrams, such as BELL, Fault, and EOL resistors.

Electrical Schematics

Style Y;Z Wiring Examples

Detailed schematics illustrating Style Y and Style Z wiring configurations with various components.

EOL Resistor Connection

Schematic showing the connection and value of the End-of-Line (EOL) resistor.

Advanced Installation Scenarios

Fault Signal Indication

Connection for fault signal indication using an open collector driver.

AC Operation Wiring

Wiring configuration for audio application using AC operation.

Board Layout and Addressing

Physical Layout

Diagram showing the physical layout of the ICC board components.

Fuse and Address Setting

Identification of the fuse location and rotary switches for address setting.

Aritech IU2080 Specifications

General

Brand	Aritech
Model	IU2080
Category	Controller
Language	English