What causes the first groove to be very narrow on my ArmaTrac Tractor?
If the first groove is very narrow when using your ArmaTrac Tractor, ensure that the lower connection arms move to the sides in a safe way, as they may be excessively strained. Adjust the carrier axle, as it may be positioned incorrectly. For issues related to track width, call your authorized dealership.
Why is my ArmaTrac 802-804 FG Tractor experiencing excessive fuel consumption?
Excessive fuel consumption in your ArmaTrac Tractor can stem from several causes. Ensure you're using clean and stabilized fuel, as an incorrect fuel type can lead to this issue. Check if excessive ballast is installed and adjust to recommended values. A dirty or clogged air filter can also contribute, so clean the filter and perform necessary maintenance. Avoid overloading the engine by shifting to a lower gear or reducing the load. Ensure the equipment is adjusted correctly. For issues related to the hydraulic system and PTO applications, it's best to call your authorized dealership.
How to troubleshoot hard steering in ArmaTrac 802-804 FG Tractor?
If the steering of your ArmaTrac Tractor feels hard or rotates with difficulty, start by checking the oil level and top it up if required. A clogged oil filter can also cause this issue, so replace the filter. Ensure that the tire pressures are at the recommended values, and replace worn tires if necessary. After starting the engine, wait for at least 3 seconds to allow the oil to be transferred thoroughly within the system.
What to do if my ArmaTrac Tractor does not operate properly?
If your ArmaTrac Tractor does not operate or operates with difficulty, first check the fuel level to ensure it is not low or empty. If the water retaining filter contains water or dirt, discharge the water. For injector faults or a clogged fuel filter, call your authorized dealership.
Why is the first groove very wide on my ArmaTrac Tractor?
If the first groove is very wide when using your ArmaTrac Tractor, ensure that the lower connection arms move to the sides in a safe way, as they may be excessively strained. Adjust the carrier axle, as it may be faulty. For issues related to track width, call your authorized dealership.
What to do if the pedals are lowered completely on my ArmaTrac 802-804 FG Tractor?
If pedals are lowered completely, call your authorized dealership, as the brake pads may be worn.
Why doesn't the position control lever operate on my ArmaTrac 802-804 FG Tractor?
If the position control lever on your ArmaTrac Tractor does not operate (dysfunctional), call your authorized dealership, as the hydraulic lifting shaft setting mechanism may be faulty or its connections may be loosened.
Why are the hydraulic arms oscillating on my ArmaTrac 802-804 FG?
If the hydraulic arms on your ArmaTrac Tractor do not react or oscillate while being used with draw control, lubricate the shaft, call the authorized dealership if it cannot be corrected, as the rear cover support shaft may be stuck. If the hydraulic side cover lever is released from its position, released off the pin and/or the spring, or if the sensitivity tap is closed in (-) position, call your authorized dealership. Also, perform the sensitivity setting again (sensitivity setting tap) and inspect the reaction setting lever, as the setting of the sensitivity setting lever may be incorrect.
What causes excessive oil consumption in my ArmaTrac 802-804 FG Tractor?
If your ArmaTrac Tractor is consuming oil excessively, reduce the oil level, as it may be higher than required. For issues related to using incorrect oil or oil leaks, call your authorized dealership.
Why is my ArmaTrac 802-804 FG Tractor making a knocking noise?
If your ArmaTrac Tractor is experiencing knocking (noisy) operation, check the radiator fluid level and clean the radiator cores, as the engine may be overheated. For issues such as low oil pressure or low oil level, call your authorized dealership.
Instructions and warnings for safely transporting and towing the tractor.
Covers headlamp, turn signal, and horn functions of the signal lever.
Provides a visual guide to various indicator symbols used on the dashboard.
Crucial safety advice regarding battery handling, charging, and potential hazards.
Describes the ALS function, control, usage, and important warnings.
A critical reminder to fasten the seat belt for operator safety.
Stresses correct ROPS usage, regular checks, and prohibits modifications.
Warns against using a folded ROPS due to driving safety risks.
Highlights the impact of low tyre pressure on wear and handling safety.
Detailed technical specifications for the 502-504 FG tractor models.
Table detailing tyre size, pressure, and load capacity for 502-504 FG.
Information on speed ratios and noise/vibration levels for 502-504 FG.
Detailed technical specifications for the 702-704 FG tractor models.
Table detailing tyre size, pressure, and load capacity for 702-704 FG.
Information on speed ratios and noise/vibration levels for 702-704 FG.
Detailed technical specifications and gear ratios for 802-804 FG models.
Table detailing tyre size, pressure, and load capacity for 802-804 FG.
Information on speed ratios and noise/vibration levels for 802-804 FG.
Diagnosing and resolving issues with engine operation, power, and knocking.
Addressing engine overheating, low temperature, and excessive fuel consumption.
Common electrical problems and their solutions, including battery and starter issues.
Diagnosing steering hardness, damper outlet issues, and leaking connectors.
Resolving issues with hydraulic arms, equipment slipping, and linkage reactions.
Troubleshooting brake pedal issues, cab dust, and air conditioning performance.
Resolving ploughing issues like difficult entry, pulling left, or narrow grooves.
Addressing wide grooves, unevenness, frame crookedness, and cut transfer issues.
To Next Page
General