Armytek Optoelectronics Inc. is a Canadian manufacturer that produces powerful and reliable flashlights designed especially for your
needs applying in them components made in the USA and Japan. .10 years no-hassle warranty
§ Superb light of amazing constant brightness due to powerful electronics and active temperature control without timers
§ Multi-flashlight “10 in 1" is for many activities: car, fishing, hunting, home, work, city, picnic, bike, outdoor, travel
§ Efficient TIR-optics and no “tunnel vision” effect even after continuous use
§ Multicolor Warning Indication of low battery level and high temperature
§ Side switch for comfortable one-hand operation and easy modes switching with advanced operation
§ Multicolor State Indication and ultra low current drain in OFF-state more than 25 years–
§ Comfortable headband for reliable fixation of the flashlight – it won’t slip even while you’re running
§ Solid body without long wires, weak rubber connectors and unnecessary boxes
§ Removable magnet in the tailcap, removable clip, strong lanyard and possibility of tail-stand for multipurpose use
§ Total protection from water, dirt and dust penetration - flashlight continues to work even at the depth of 10 meters
Wizard
Warnings
Armytek Optoelectronics Inc. shall not be liable for any harm done to the user if it
was caused by improper use of the product.
1. Always follow the instructions from this manual and recommendations on battery usage.
2. Apply only the recommended power sources.
3. Do not reverse battery polarity.
4. Do not use different power sources together, i.e. old ones with new ones, charged with
discharged. Do not use different types of batteries combined as the element with less
capacity can be damaged.
5. Do not modify or recast the flashlight and its components as it will deprive you of the
warranty.
6. Do not allow water or any other liquid to leak into the flashlight.
7. Do not aim a turned-on flashlight at people's or animals' eyes – it can cause temporary
blindness.
8. Do not allow children to use the flashlight without your assistance.
Care and Storage
It is recommended to clean the threads and O-rings off dirt and old grease. Remember that secure protection from water and dust
cannot be provided by worn out sealing. And fouling as well as lack of lubricant cause fast wear-out of threads and sealing rings.
To clean the threads do the following:
1. Unscrew the tailcap and remove the sealing ring carefully with a toothpick (do not use sharp metal things as they can damage the ring).
2. Wipe the sealing ring thoroughly with a soft cloth (or tissue). Do not use solvents. If the sealing ring is worn out or damaged
replace it by a new one.
3. Clean the metal threads with a brush using ethanol. Be careful not to allow applied liquid to get inside the flashlight or tailcap as it
can cause fails in functionality of the flashlight.
After cleaning lubricate the thread and the sealing ring with polyalphaolefin-based silica grease, e.g. Nyogel 760G.The application of
automotive and other improper grease can cause swelling and damage of the sealing rings.
In case of active operation and exploitation in dusty environments, it is recommended to perform cleaning and lubricating of the parts
as often as required, even if it is more than twice a year.
Service and Warranty
Specifications are subject to change without notice.
Armytek provides free warranty repair for 10 years from the purchase.
Warranty doesn't cover damage caused by:
1. Improper usage.
2. Attempts to modify or repair the flashlight by nonqualified specialists.
3. Longtime application in chlorinated or polluted water, or other liquids (other than water).
4. High temperatures and chemicals' exposure (including the exposure of liquid from defected batteries).
5. Usage of low-quality batteries.
Armytek Optoelectronics Inc.
Web: www.armytek.com Email: service@armytek.com
Address: 67 Vandervoort Dr, Richmond Hill, Ontario, L4E 0C7, Canada
With ambient temperature +25°C the flashlight delivers light in Maximum mode for about 6-10 minutes and then the brightness
decreases by 35%. After cooling-down (provided that battery voltage is sufficient) the brightness increases to the Maximum mode
again. This stepping goes cyclically to maintain the user's safety and the flashlight's functionality. In conditions of good air-cooling the
flashlight delivers constant light even in Maximum mode. There are no preset timers for stepping, but real-time active temperature
measurements.
* Light outputs for flashlights with Warm light are about 7% less, beam distances are about 3% less.
We recommend NOT to leave power sources inside the flashlight for a long storage period, as batteries (especially, non-rechargeable) can leak for
various reasons and damage the inner parts of the flashlight. If you want to keep your flashlight in a stand-by state with batteries in, use new and
quality batteries, store the flashlight in acceptable for batteries operational temperature and revise the batteries' state at least once a month. If you
have noticed any signs of batteries' defects, withdraw them from the flashlight and take out of operation. It is also recommended to replace
discharged batteries with new ones before the storage as the chance of leakage is higher with discharged batteries.
We highly recommend NOT to use CR123A batteries as a power source for often and continuous flashlight’s operation.
Remember that old or low-quality disposal batteries can be damaged under heavy load and explode.
To Next Page
Need help?
General
