To Next PageTo Next PageWhat to do if my ARO Burner does not ignite immediately?
If your ARO Burner doesn't ignite immediately, try the following: * Ensure that the gas valves are open. * Check if sparks are produced when igniting the appliance. * Push the control knob(s) for 5 seconds before you attempt to ignite the appliance. * Ensure that the burner(s) is / are clean. * Check if the gas cylinder(s) is / are not empty.
Why is my ARO Burner taking a long time to heat up?
There are a couple of reasons why your ARO Burner might be taking a long time to heat up: * The appliance takes longer to heat up when it is cold outside. * If the gas supply is not sufficient because there is not enough gas in the gas cylinder(s), refill or replace the gas cylinder(s). * Check if the gas hose(s) is / are blocked or clogged.
What to do if my ARO SRGG31403A does not ignite at all?
If your ARO Burner doesn't ignite at all, it could be due to several reasons: * The electrode may be covered with cooking residues. Use a clean swab and alcohol to clean it. * The electrode or wire may be damaged. Replace it with a new electrode assembly with wire. * The wires of the electrode are loose or have fallen off. Replace them with a new electrode assembly with wire. * The orifice may be blocked. Clear the orifice. * The electrode may not be aimed at the burner hole. Align the electrode and the burner hole, adjusting the distance between the metal pin of the electrode and burner hole to 3 - 5 mm.
How to fix flare-ups on my ARO SRGG31403A Burner?
Flare-ups on your ARO Burner can occur due to: * Excessive fat content in the meat. Remove part of the fat before grilling. * Try to reduce the temperature. * Clean the burner if you spot deposits of grease.
Why is my ARO SRGG31403A Burner flame not blue?
A non-blue flame in your ARO Burner could be caused by: * Too much or too little air being supplied. * The burner being misaligned. * In case of incomplete combustion contact specialist.
What to do if my ARO SRGG31403A only heats up to 100-150°C?
If your ARO Burner only heats up to 100-150°C, consider the following: * Check the thermometer's functionality by comparing its reading with an oven thermometer placed inside the appliance. * Inspect all gas connections for leaks and tighten them if necessary. * Ensure the gas hoses are straightened if bent or kinked. * Clear any blockages in the burners or orifice. * Have your gas dealer check the gas cylinders for low pressure. * Refill or replace gas cylinders if the gas supply is insufficient.
What to do if my ARO Burner cannot be ignited by a match?
If your ARO Burner cannot be ignited by a match: * Open the valve of the gas cylinder(s) and / or the pressure regulator(s), if no gas is being fed to the burner(s). * Clear the tubes of the burner(s) if the gas flow is not smooth. * Re-assemble burner(s) and valve(s) if you deem the assembly to be incorrect. * WARNING! Turn all the control knobs to the off positions, if any burner does not ignite within 5 seconds. Wait for 5 minutes to let the gas dissipate and try again.
Why does the pressure regulator make noise in my ARO Burner?
If the pressure regulator in your ARO Burner is making noise: * Check if the ventilation opening on the pressure regulator is plugged. Unplug the opening and wait 5 minutes before starting again. * Check if the ventilation openings are covered up. Check the appearance of the flames and remove possible plugging.
Why is there no spark noise in my ARO Burner?
If there's no spark noise in your ARO Burner, the electrode may not be aimed at the burner hole. Align the electrode and the burner hole, and adjust the distance between the metal pin of the electrode and the burner hole to 3 - 5 mm.
General safety advice specific to barbecue operation.
Safety precautions specific to gas barbecue operation.
Warnings regarding gas connections, cylinders, and regulators.
Steps for assembling the barbecue, emphasizing care and instructions.
Procedure for checking gas connections for leaks to ensure safety.
Step-by-step guide to ignite burners using the built-in electronic igniter.
Step-by-step guide to ignite burners manually using a match.
Detailed steps for cleaning the barbecue after use, including surfaces and trays.
Regular checks and upkeep procedures for the barbecue.
Instructions and recommendations for storing the barbecue properly.
Safety precautions and methods for transporting the barbecue.
General