Evolulion
2.SM &
Evo/ulion-EV
2.SM
Vortex
2.SM &
Vor/ex-ET
2.SM
Kit Contents
- Fiberglass fuselage pod with canopy - composite
- Tapered tail boom - carbon/glass-composite
- 4-segment Wing - pre-sheeted and sanded
- V-tail halves w/hinged rudevators - Evolution
- V-tail mount
& triangle plate - Evolution
- Composite plate with M3 bolts and nylon retainers - Evolution
- V-tail control horns
(2)
- Evolution
- Vertical stabilize
r-
carbon/Glass composite - Vortex
- Rudder- balsa laminated - Vortex
- Horizontal stabilizer- balsa laminated w/hinged elevator -Vortex
- Wing Tip Joiners rods - carbon
(4)
- Wing
Bo
lt
M4
(1-metal, 1
ny
lon)
- Nylon retainer with M2 bolt for horizontal stabilizer (2) - Vortex
-
Control horn for Horizontal stabilizer (1) - Vortex
- Control horn for rudder (1) - Vortex
-
CA hinges for rudder
(2)
- Vortex
-
Control Horns for the Ailerons and the Flaps (4)
-
Pushrod wire for Aileron and Flap
(4)
- Push rod set for elevator and Rudder (2)
- Joiner tube for Elevator pushrod tubes (1)
- Fiberglass cloth
- Glider Drawing
Art Hobby guarantees this kit to be free from defects
in
material
and workmanship, at the date of purchase. This does
NOT
cover any components damaged by use, misuse, or
modification.
In
no case shall Art Hobby's liability exceed the
original cost of the purchased product.
In
that Art Hobby has no
control over the final assembly or material used for final
assembly, no liability
shall
be
assumed for any damage
resulting from the use by the user of the final user-assembled
product. By the act of using the final user-assembled product,
the user accepts
all resulting liability.
Radio
Control Hobbies are not toys but rather high
performance models that could produce harm.
Always put safety first when using this product.
If
this is
your
first 'mode/, please
seek
Ihe
adv
,ic'e
..
of
othe~
experienced
.
mopelers
prio~
;
to
assembly
and
fHght.
. ,A'n
internationally recognized
nonpr9fil
sanctioning
organlzatioq
for
.
modeling
is
Ihe Academy
of
Model
Aeronautics
. They can provide club,
field
,
and
liability
insurance
information.
Contact them
for
information at:
AMA
5151
East Memorial Drive
Muncie,
IN
47302·9252
(800) 435·9262
Fax: (765) 289·4248.
Internet:
. .
,
www
."'!odel,aircraft.org, ,:
Check the Items Needed, Tools and
Supplies,and
Contents,
s~ctions
.
V'lrify the. contents
of
the
kit
and
, your supplies before continuing.
If
'you'
have
"any Qther problems
or
questions, please eontaefcustoiner
sei'vlee
In
the U.S.A. at:
.
.,
Customer Service
1122'Ginger Ave.
Billings,
MT
59105
(406) .545-4118
Email:
9 liders@arthobby.com
Visit
us
at
.:. wwW.arthobby.com
Recommended Radio & Drive
Components
Glider
&
Electro·glider:
- 6-ch.+ Radio system:
Aurora-9 Hitec,
RDS800FHSS Airtronics or similar
- 6 ch.+ Receiver
Optima-6/7 Hitec (#H2841
0, H28414)
RX
-700Airtronics (#H92674) or similar
-
Servos:
Ailerons/spoillerons
- HS-65MG;
HS-82MG (#H32065,H32082)
Flaps (optional)
-
HS-85MG (#H31085)
V-tail
-
HS-65HB (#H33065)
Elevator
-
HS-65MG (#H32065)
Rudder
-
HS-65HB (#H33065) - tail
-
Servo wire extensions:
2x
36"
(#HOOX36)
- ailerons
2x
24"
(#HOOX24)
- flaps
or
100 Inches of Servo Wire to make your own extensions
- Universal wing servo covers x 2
(#A0031)
Electro·glider:
- ART-2000 outrunner motor
-
41
mm spinner + 16x8 CAM Aeronaut
(#A041 S5 + A01680)
or
-
40 mm spinner + 15x8 CAM Aeronaut
(#A040S5 + A01580)
- ESC 36 - 54 Amp
(#M70360, M70500, M70540)
- 2200 - 2500mAh, 3-cells LiPo
(#B118160, B182265)
Tools & Supplies
- Hobby Knife (blade #11)
- 5 Minute Epoxy
(#A0201).
(use for joining the wing panels and tail)
-
20 Minute Finishing Epoxy (#A0209)
(use for fiber glassing joints)
-
CA adhesive (#A0101).
- Masking tape
-
Pliers
- Drill
- Drill Bits: 2mm, 4mm, 6mm
-
Soldering Iron
- 1 meter ruler
- Flexible metal ruler (Approximately
250mm long will be
easiest to use)
-
Clear lacquer (DEFT- brand) or similar.
-
400 grit sand paper.
Evo-Vortex
v.
01
To Next Page
Need help?
General