EasyManua.ls Logo

Asda KS-108 User Manual

Asda KS-108
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
ASDA$BLACK$RADIO$ALARM$CLOCK$$MODEL$KS$-$108$
Digital$radio$tuning$
Bright$red$LED$digital$display.$
No$battery$back-up$in$case$of$power$failure.$
Not$able$to$store$stations$on$the$radio.$
12$hour$display,$with$“pm”$led$on$to$show$PM$
$
Plug$in$mains.$Display$flashes$12:00$
To$set$time,$press$$“time$set”.$The$red$digital$time$display$flashes.$Press$“hours”$
and$“minutes”.$Display$continues$to$flash$for$2-3$seconds,$then$is$steady$and$the$
time$is$now$set.$
$
Listen$t o$the$radio:$Extend$the$small$thin$black$wire$as$high$as$possible.$It$is$the$
FM$aerial.$To$help$AM$reception,$rotate$the$radio$left$or$right,$its$aerial$is$inside$
the$ device.$ Each$ time$ you$ press$ “clock/fm/am”,$ the$ device$ rotates$ around$ the$
three$$states.$
To$tune$in$the$radio,$press$and$hold$ “tuning$ +”$ or$“tuning$-”$for$2$seconds$and$
radio$ will$ auto$ tune$ to$ next$ radio$ station.$ If$ you$ know$ the$ frequency,$ keep$
pressing$ until$ frequency$ is$ displayed.$ You$ cannot$ store$ stations.$ Adjust$ the$
volume$+$or$-.$
$
To$set$alarm.$Radio$must$be$off.$
Press$ “alarm$ set”$ quickly$ once.$ Digital$ display$ flashes.$ Press$ “hours”$ and$
“minutes”$to$display$required$alarm$time.$There$is$also$a$small$red$LED$“alarm”$
which$ flashes$ on$ and$ off.$ This$ small$ red$ LED$ $ is$ steady$ when$ an$ ala rm$ is$ set.$
Select$the$time$quickly,$because$if$no$buttons$are$pressed$for$about$two$seconds,$
the$alarm$time$is$stored$and$the$flashing$“alarm”$LED$is$now$steady,$showing$the$
alarm$time$is$set$and$the$alarm$is$now$on.$$
$$
Be$aware$also$that$the$type$of$alarm$has$also$to$be$selected.$The$ al arm$can$be$the$
radio,$either$FM$or$AM,$or$can$be$a$loud$buzzer.$To$select$the$type$of$alarm,$when$
you$ are$ in$ the$ alarm$ setting$ mode$ (with$ the$ digital$ display$ flashing)$ press$ the$$
“alarm$mode”$button$and$each$press$will$rotate$selection$of$“FM/AM$/Buzzer”.$
There$are$small$red$LEDs$to$show$what$is$being$selected$as$your$alarm.$
$
To$check$the$alarm$time$at$any$time$just$press$once$the$“alarm$set”.$The$digital$
display$ will$ flash$ with$ the$ alarm$ t ime$ and$ show$ whether$ FM,AM$ or$ buzzer$ is$
primed.$
$
You$may$cancel$the$alarm$at$this$or$any$point$by$pressing$“alarm$mode”,$or$you$
can$ chan ge$ the$ al arm$ time$ from$ its$ sett ing$ by$ following$ the$ above$ stages,$
resetting$the$new$time$whilst$the$large$display$is$still$flashing.$
$
SNOOZE:$Going$to$bed…switch$the$radio$on,$then$press$“snooze”$button$to$select$
how$ long$ before$ radio$ switches$ itself$ off.$ Each$ time$ the$ “snooze”$ button$ is$
pressed,$ you$ will$ see$ a$ countdown$ display$ of$ the$ time$ in$ ten$ minute$ intervals$
from$90$mins$down$to$“off”$before$the$radio$will$switch$off$for$the$night..$If$you$
just$press$“snooze”$once,$the$radio$will$play$for$90$minutes$and$then$switch$off.$
$
Question and Answer IconNeed help?

Do you have a question about the Asda KS-108 and is the answer not in the manual?

Asda KS-108 Specifications

General IconGeneral
BrandAsda
ModelKS-108
CategoryAlarm Clock
LanguageEnglish

Summary

Radio Setup and Basic Operation

Setting the Clock Time

Instructions on how to set the digital time display by pressing the 'time set' button and adjusting hours/minutes.

Listening and Tuning the Radio

Guidance on extending the FM aerial, rotating for AM reception, and using tuning buttons to find stations.

Alarm Functionality

Setting the Alarm

Steps to set the alarm time, noting the red LED indicator and confirmation of alarm status.

Selecting Alarm Type

How to choose between FM/AM radio or a buzzer alarm using the 'alarm mode' button.

Checking and Cancelling Alarms

Procedures for checking the set alarm time and cancelling it by pressing 'alarm mode'.

Snooze and Display Dimming

Using the Snooze Function

How to set the snooze timer to turn the radio off automatically in 10-minute intervals.

Display Dimmer Control

Explanation of the 'dimmer' switch to adjust display brightness between two pre-set levels.