QUICK START PROCEDURES
1. Load the dishwasher. (There’s no need to pre-rinse. Simply scrape off large food particles before you 3, 4
load the dishware.)
2. After you’ve pushed the baskets back inside the unit, manually rotate the upper and lower spray arms 3
to be sure they turn freely. Rearrange any item that blocks the wash arms.
3. Add 1 to 3 tablespoons of automatic dishwashing detergent and close the dispenser cover. 5
4. Make sure there is rinse aid in the dispenser. Add rinse aid, if needed. 6
5. Press the main power button on the far left side of the inner door panel to turn on power to the machine.
6. Press the Program button until the desired program displays.
7. If desired, set program options by pressing Menu until the option you wish to select displays. Press Set until
the desired setting displays, then press Menu to confirm your selection.
8. Press the Start/
Stop button.
9. Close the door securely. (You should hear it click shut.) The dishwasher will start.
Refer to this page in
the Use & Care Guide.
INTERRUPTING A PROGRAM TO ADD AN ITEM
If you want to interrupt a program to add an item, open the door slightly until the spray arms stop turning. You can then open the door fully and
place the item into the dishwasher. Close the door securely. The program will continue from where it was interrupted.
WARNING! Be extremely careful when opening the door during a program. The water is hot and you could get scalded.
CHANGING OR STOPPING A PROGRAM
If you decide to change the program after you have started the machine, press the Start/Stop button for three seconds. You will have to select
the program and options again when you are ready to restart the program. (Note: If the program has already gone through the wash cycle,
you will have to add detergent.)
CHILD-SAFE BUTTON LOCK
To prevent a child from accidentally starting the dishwasher or changing the program settings, the dishwasher can be programmed not to
start unless two buttons are held down simultaneously. Refer to your Use and Care Guide for instructions on how to activate this feature.
END-OF-PROGRAM SIGNAL
The dishwasher emits a short signal at the end of the program. Refer to your Use and Care Guide for instructions on how to adjust the volume
or to deactivate the signal.
DISHWASHING DETERGENT AND RINSE AID
We recommend that you use only unscented, granular automatic dishwashing detergent. Generally, one tablespoon of detergent is needed
for a normal wash load. More heavily soiled items, however, may need more detergent. (See page 5.) In any case, you should never use
more than three tablespoons of detergent.
Using liquid rinse aid prevents water spots from forming on dishes and improves drying by allowing water to “sheet” off the dishes. The rinse
aid is released during the final rinse. For information on how to fill the rinse aid dispenser and control the amount released, refer to page
6 in your Use and Care Guide. NOTE: If you use a dishwashing detergent with a rinse aid additive, you should not fill the rinse aid
dispenser.
START/STOP BUTTON
Once you have selected the wash program and options, press this button to start the dishwasher. (Make sure the door is securely closed.)
The indicator light around the button will glow progressively as the program goes through each cycle. When the program is complete, the
light will glow all the way around the button.
Temperature
The temperature can be changed in all programs, except Auto wash,
Rinse and Hold, and Rinse and Dry. Your choices are: cold, 85°,
105°, 120°, 130°, 140°, 160°, and 170° F. (Note: The Delicate and
Quick wash programs cannot be set over 140° F.) To select a
temperature, press the Menu button until Temperature displays,
then press the Set button until the desired setting displays. Press
Menu to confirm your selection.
Drying
This lets you select how long the turbo fan runs after the final rinse.
You have three options: Short, Normal, or Extra drying. (Note: This
option is not available with the Auto wash, Rinse and Hold and
Rinse and Dry programs.) To set the drying time, press Menu until
“Drying” displays, then press Set until your preference displays.
Press Menu to confirm your selection.
Express
This option reduces the wash time and lowers the wash temperature
by 20° F. (Note: This option is not available with the Quick Wash
and Rinse and Hold Programs.) Select this option by pressing
Menu until Express displays, then pressing Set until your preference
displays. Press Menu to confirm your selection.
Cool Touch
This option lets you set a cool-down cycle after the drying program.
Press Menu until Cool Touch displays, then press Set once to select
On or twice to select Off. Press Menu to confirm your selection.
NOTE: There are more programming options available. Refer to
your Use and Care Guide for details.
Art. 8075645
Refer to your Use and Care Guide for additional information.
To Previous Page
Loading...
Need help?
General
