Home
Assa Abloy
IP Access Controllers
VingCard Allure
Assa Abloy VingCard Allure User Manual
4
of 1
of 1 rating
54 pages
Give review
Manual
Specs
To Next Page
To Next Page
Loading...
1
A
S
S
A
A
B
L
O
Y
H
o
s
p
i
t
a
l
i
t
y
Us
er Ma
nual
VingCard
A
ll
ure
2
Table of Contents
Default Chapter
3
Table of Contents
3
FCC/ISED (IC) Statements
6
FCC Statements for LCU 6333/6334
6
ISED (IC) Statements for LCU 6333/6334
6
FCC Statements for BLE Module
7
ISED (IC) Statements for BLE Module
7
Déclarations D' Industry Canada Pour Module BLE
8
1 Introduction
9
2 Installation
11
Installation Checklist
11
To Install a Main Control Unit
12
To Fasten the Main PCBA to the Electronics Housing
12
To Fasten the LCU
12
To Fasten the Electronics Housing
12
To Fasten the Main PCBA to the Input/Output
12
To Connect a Frame Communication Unit
13
To Install a Zigbee Endnode
13
To Install a BLE Module
14
To Install an Ethernet Module
15
To Connect a Door Unit 3012
17
To Connect a Door Opener
17
To Connect a Doorbell
18
To Connect an Electric Strike
18
To Connect an Egress Switch
19
To Install an Access Panel (Grand)
19
To Install a Wired Room Panel
21
To Connect a Wired Room Panel to an Access Panel (Grand)
24
To Connect a Wired Room Panel to a Room Status Panel (Blend)
24
To Install Frame/Door Communication Units
25
Installation
25
Battery-Low Warning
26
Battery Replacement
26
To Install a Junction Box (New Installations)
27
Large Junction Box
27
Small Junction Box
27
To Install a Junction Box (Existing Installations)
28
Large Junction Box
28
Small Junction Box
28
To Install a GPIO Module
29
To Connect a GPIO Module
30
To Power Supply a GPIO Module
32
To Communicate with a GPIO Module
32
Example 1: Connecting to Chic Corridor Panel
32
Example 2: Connecting to Main Control Unit
33
GPIO Module Inputs
34
Example 1: Connecting Dry Switches for DND and MUR
34
Example 2: Connecting DND and MUR Signals from 12V or 24V PLC
34
GPIO Module Outputs
35
Example 1: Connecting to Doorbell
35
Example 2: Connecting to External DND and MUR Signal Lamps
35
3 Main Control Unit
36
Battery Backup
36
4 GPIO Module
37
To Configure a GPIO Module
37
To Upgrade Firmware in a GPIO Module
38
5 Ethernet Module
39
To Connect an Ethernet Module to the Visionline Server
39
Web Interface
40
To Factory Reset an Ethernet Module
41
Boot-Up Procedure
41
More about Finding the Server
43
To Commission Ethernet Modules with DNS
43
Single Server
43
Multiple Servers
44
To Commission Ethernet Modules Without DNS
44
To Switch to Backup Server with DNS
45
Single Server
45
Multiple Servers
45
To Switch to Backup Server Without DNS
45
6 Corridor Panels
46
To Connect a Room Status Panel to an Access Panel
46
To Change Color of a Panel
47
7 Wired Room Panels
48
To DIM the Light on a Wired Room Panel
48
8 Troubleshooting and Maintenance
49
To Reset the Main Control Unit
49
To Remove an Access Panel
49
To Reset the Tamper Switch
50
To Power Open an Access Panel
50
To Emergency Open a Door Communication Unit
50
Appendix: Quick Reference of Technical Data
51
Main Control Unit
51
Room Bus Cable
51
Access Panel
51
Room Status Panel
51
Wired Room Panel
52
Frame Communication Unit
52
Door Communication Unit
52
Ethernet Module
52
Junction Box, New Installations
53
Junction Box, Existing Installations
53
GPIO Module
53
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Assa Abloy VingCard Allure and is the answer not in the manual?
Ask a question
Assa Abloy VingCard Allure Specifications
General
Brand
Assa Abloy
Model
VingCard Allure
Category
IP Access Controllers
Language
English
Need help?
General
To Next Page