ASSEMBLY
Introduction
• The Assault Fitness AirRunner treadmill requires only minor assembly. All tools required to complete the initial
setup and assembly have been included in the Assembly Hardware Kit.
• Remove the unit and all parts from the carton and packaging. Conrm all parts shown in the section titles As
Shipped are included before attempting assembly of the AirRunner.
Assembly Step One: Upright Installation
• Locate the Speed Sensor Cable – Lower (549a) and ensure the end/connector is extending from the main
frame.
• Raise the Upright – Left vertically, ensuring the Keyholes are located at the bottom. Align the Upright - Left
keyholes with the two posts located on the main frame. This will support the upright while completing the
installation.
• Connect the Speed Sensor – Lower (549a) and Speed Sensor Cable – Middle (560b) connectors rmly.
• Locate three (3) sets of #534 Hex Screws and #562 Flat Washers, and loosely thread each assembly through the
Left Upright and into the main frame. Tighten the screws rmly.
• Hang the Upright – Right keyholes onto the Main Frame posts and install the remaining three (3) sets of #534
Hex Screws and #562 Flat Washers.
Assembly Step Two: Sidecase Covers
• Locate the Sidecase Center Cover - Left (507). Align the tabs locate at the top with the receivers on the installed
sidecase plastics. To install, the cover will hinge downward and snap in place. Ensure the outer surface of the cover
is ush or aligned with the adjacent plastics.
• Secure with two (2) #537 Phillips Head Screws.
• Remove the four (4) #564 Hex Screws
from the backside of the Console (514)
and set them aside.
• Connect the Console Cable (514a) and
Speed Sensor Cable – Upper (559b)
connectors and carefully tuck the excess
cable into the Handrail.
• Loosely thread the four (4) #564 Hex
Screws through the mounting plate on
the Handrail and into the backside of the
Console (514). When all four (4) screws
are installed, tighten rmly.
• With the help of a second person, support
the Handrail assembly above the uprights
and connect the Speed Sensor Cable –
Upper (559b) and Speed Sensor Cable –
Middle (560a) connectors. Carefully tuck
the connectors and excess cables into the
left Upright.
• Set the left and right Handrail brackets
inside the left and right Uprights. While
supporting the Handrail Assembly,
loosely thread three (3) #535 Button
Head Hex Screws through the left
Upright and into the Handrail bracket.
Assembly Step Four – Final Adjustments
• Identify a suitable location that is level and oers enough space for the unit with the minimum required free
space. It is recommended that the AirRunner be sited with a minimum of 0.5 meters (19.7 in.) of clearance from
the nearest walls or other equipment to the left, right and front of the unit. A minimum of 2.0m (79”) of clearance
should be maintained to the rear of the AirRunner.
CAUTION: THIS TREADMILL IS HEAVY. INJURY CAN OCCUR IF PROPER LIFTING TECHNIQUES
ARE NOT PRACTICED.
• To relocate, raise the rear of the unit with by grasping the transport handle and slowly rolling the AirRunner to
the desired location.
• Ensure the unit is level and does not rock by adjusting the Stabilizer Leveling Feet. Two feet are located at the rear
of the main frame. As a starting point, loosen each foot by threading the assembly downward/clockwise, and
then thread the locknuts downward (clockwise) against the base of the foot. Check the unit for stability and make
any adjustments as necessary. Once stable, lock the Stabilizer Leveling Feet in place by tightening the jamb nut
upward/counter-clockwise, against the underside of the frame to lock the current positions for each foot.
• Congratulations. The assembly of your Assault Fitness AirRunner treadmill is complete. Please read all included
information, user guides and warnings before use.
Assembly Step Three – Handrail & Console Installation
Repeat this step for the right side and tighten all six (6) screws rmly.
• Align the Console Cover – Left Outer (528) with the outside of left Handrail bracket, and thread two (2) #537
Phillips Head Screws through the handrail bracket and into the #528 Cover. Repeat this step for the right side
with Console Cover – Right Outer (531).
• Align the Console Cover – Left Inner (529) with the inside of the left Handrail bracket install two (2) #537
Phillips Head Screws through the #529 Cover and into the #528 Cover.
• Align the Console Cover – Right Inner (530) with the inside of the right Handrail bracket and install two (2)
#537 Phillips Head Screws through the #530 Cover and into the #531 Cover.
5803 Newton Drive Carlsbad, California 92008 Ph. 1.888.815.5559
For more information or questions regarding your equipment, please visit our website at
AssaultFitnessProducts.com
© Assault Fitness 2017
514a
514
Handrail (504)
535
535
535
535
535
535
Upright
528
560a
559b
537529 530
531
537
564
504 559b
Stabilizer
Leveling
Foot
Part #23-AS-566 US-English v1.0 05-Mar-17
To Next Page
Need help?
General