Page 1
EUROHV103 (1.3mm Nozzle Size)
EUROHV105 (1.5mm Nozzle Size)
EUROHV107 (1.7mm Nozzle Size)
EUROHV109 (1.9mm Nozzle Size)
EUROPRO FORGED HVLP
SPRAY GUN WITH PLASTIC CUP
EUROPRO FORGED HVLP
SPRAY GUN WITH PLASTIC CUP
MADE IN TAIWAN
DURABLE & LIGHTWEIGHT
• Forged body provides longer tool life
• Anodized body for corrosion protection
• Internal coated passages
• Stainless steel needle and fluid tip
• Slick finish for faster & easier cleaning
• Lightweight: 325 grams (0.7 Lbs)
HIGH EFFICIENCY
• Unique pattern designed for great coverage, optimal overlapping
• Low overspray (bounce back)
• Great transfer efficiency
• Superior atomization
• Innovative, advanced HVLP technology
QUICK THREAD TECHNOLOGY
• 1 Turn to lock/unlock the air cap
• 3 Turns to lock/unlock the fluid tip
• Wide threads for easy cleaning
• M16*P1.5 female thread fluid joint
• Compatible with most traditional and disposable cup systems
SMOOTH OPERATION
• Soft trigger pull to reduce fatigue
• Precise lubricated adjustment knobs for better control
• Innovative CNC machining to avoid the need for gaskets behind the fluid tip
Nozzle Size:
Cup Capacity:
Operation Pressure:
Weight:
Gun Dimensions W x H:
Avg. Air Consumption:
Air Inlet Thread NPT:
Required Compressor:
Max. Pattern at 4" to 7" Distance:
Air Cap Output:
Air Hose I.D. Size:
1.3mm, 1.5mm, 1.7mm or 1.9mm
600ml
29psi
0.7lbs. (325g)
7" x 5-3/4" (175mm x 145mm)
9-10cfm
1/4"
2-5hp
9"-10
1
/4" (230-260mm)
10psi
6-8mm
PRODUCT INFORMATION:
SPECIFICATIONS:
IMPORTANT
The Astro EuroPro Spray Guns are designed to spray the following
solvent and waterborne light to medium viscosity materials: Enam-
els, lacquers, polyurethane, urethane top coats, urethane basecoat,
urethane clearcoat and all primers. Materials which are acidic,
abrasive and/or contain benzene must not be used. In order to
achieve the best results, surface and paint preparation must be
completed in accordance with paint manufacturer’s instructions and
recommendations. The Astro EuroPro Guns are intended to be used
only by professionally trained individuals. Strict compliance of
applicable local and national regulations must be followed.
When unpacking, check the parts diagram and part number
listing on page 3 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
Unpacking
www.astrotools.com
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
• Astro Pneumatic Tool Co. warrants our products to the original user against
defective material or workmanship for a period of 1 year (except where noted on our
price schedule) from the date of 1st use. Astro reserves the right to determine
whether the product failed because of defective material, workmanship or other
causes and to charge back for missing parts. Astro Pneumatic Tool Co., at its
discretion, will repair products covered under this warranty free of charge. The
distributor should direct the original user to return the product (with the exceptions
listed below) with the distributor’s name, address, adequate proof of date of
purchase or a copy of warranty card, and a short note explaining the problem.
Failures caused by accident, alteration, or misuse are not covered by this
warranty.
• Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user and
may not be transferred to subsequent owners.
• This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do
not allow the exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you.
1 YEAR LIMITED WARRANTY
To Next Page
Need help?
General
