Asus H170I-PRO - SATA and USB 2.0 Connectors

1-4
Chapter 1: Product introduction
9. USB 2.0 connector (10-1 pin USB910, USB1112)
ThisconnectorisforUSB2.0ports.ConnecttheUSBmodulecable
toanyofthisconnector,theninstallthemoduletoaslotopeningat
thebackofthesystemchassis.TheseUSBconnectorscomplywith
USB2.0specicationsandsupportsupto480Mbpsconnection
speed.
USB+5V USB_P11- USB_P11+ GND NC
USB+5V
USB_P12-
USB_P12+
GND
USB1112
PIN 1
6. Speaker connector (4-pin SPEAKER)
The4-pinconnectorisforthechassis-mountedsystemwarningspeaker.
The speaker allows you hear system beeps and warnings.
+5V GND GND Speaker Out
SPEAKER
PIN 1
7. System panel connector (10-1 pin F_PANEL)
Thisconnectorsupportsseveralchassis-mountedfunctions.
PIN 1
PWR BTN
PWR_LED+ PWR_LED- PWR GND
HDD_LED+
HDD_LED-
Ground
HWRST#
(NC)
F_PANEL
+PWR LED
+HDD_LED RESET
• SystempowerLED(2-pinPWR_LED)
This2-pinconnectorisforthesystempowerLED.Connectthe
chassispowerLEDcabletothisconnector.Thesystempower
LEDlightsupwhenyouturnonthesystempower,andblinks
when the system is in sleep mode.
• HarddiskdriveactivityLED(2-pinHDD_LED)
This2-pinconnectorisfortheHDDActivityLED.Connectthe
HDDActivityLEDcabletothisconnector.TheHDDLEDlights
uporasheswhendataisreadfromorwrittentotheHDD.
• ATXpowerbutton/soft-offbutton(2-pinPWR_BTN)
This connector is for the system power button.
• Resetbutton(2-pinRESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot
without turning off the system power.
8. Intel(R) H170 Serial ATA 6Gb/s connectors (7 pin SATA6G_3~6, SATAEXPRESS)
TheseconnectorsconnecttoSerialATA6.0Gb/sharddiskdrivesvia
SerialATA6.0Gb/ssignalcables.
IfyouinstalledSerialATAharddiskdrives,youcancreateaRAID0,
1,5,and10congurationwiththeIntel
®
RapidStorageTechnology
through the onboard Intel
®
H170chipset.
• Theseconnectorsaresetto[AHCI] by default. If you intend to
createaSerialATARAIDsetusingtheseconnectors,setthe
SATAModeitemintheBIOSto[RAID].
• BeforecreatingaRAIDset,refertothemanualbundledinthe
motherboardsupportDVD.
• TheSATAEXPRESSconnectorcansupportoneSATAExpress
deviceortwoSATAdevices.
SATAEXPRESS
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXN1
RSATA_RXP1
GND
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXN2
RSATA_RXP2
GND
Floating
Device_Reset
GND
Detection
SATA6G
GND RSATA_RXP4 RSATA_RXN4 GND RSATA_TXN4 RSATA_TXP4 GND