MMaasst st syysstteem / m / RReeppaair ir iinsnsttrruuccttiioonns / s / SSttrraaddddlle le lififtt 66..3355
Straddle liftStraddle lift
Adjusting the straddle liftAdjusting the straddle lift
1.1. Place Place the trthe truck ouck on a len a level flvel floor anoor and lowd lower the er the forks forks and thand the ade adjustabjustable strle straddladdle lift.e lift.
2.2. Check Check that that the dithe distanstance bece betweetween the n the floor afloor and top nd top of thof the forke forks corrs corresponesponds wids withth
tabletable 6.56.5below. Measure at four points:below. Measure at four points:
- at each fork tip- at each fork tip
- at the - at the back of the fork on each sideback of the fork on each side
3.3. ChecCheck that k that the dithe distancstance is the e is the same same betwebetween masen mast and gt and guiduides. If nes. If necesecessary asary adjust djust toto
the same distance with the adjusting screws, both at the top and bottom.the same distance with the adjusting screws, both at the top and bottom.
4.4. The latThe lateral eral play iplay in the mn the mast shast should ould be mabe max 0-0x 0-0.5 mm.5 mm. Bec. Because ause of the of the inexacinexactitudetitude
in the linearity of in the linearity of the mast section a play of max 1.5 the mast section a play of max 1.5 mm is permitted at the mm is permitted at the “worst“worst
point”, raised or lowered.point”, raised or lowered.
This means that if for example the play is This means that if for example the play is 0.5 mm with the straddle li0.5 mm with the straddle lift raised, theft raised, the
play with the straddle lift it play with the straddle lift it its lower position should be max 1.5 mm, and theits lower position should be max 1.5 mm, and the
reverse.reverse.
5.5. Check Check the the play bplay betweetween the en the roller roller surfacsurfaces on es on the the mast amast and guind guidesdes. For . For permitpermittedted
playplay see "Adjusting the play in the mast" see "Adjusting the play in the mast" on page 6.15on page 6.15, 160 mast., 160 mast.
6.6. ChChececk thk that at ththe fe fororks ks arare he horiorizozontntalal..
7.7. If the fIf the fork tiork tips pops point upint upwards wards the sthe shims ohims over thver the pree pressure ssure plate plate shoushould be ld be removremoveded
(on the assumption that the forks are straight).(on the assumption that the forks are straight).
8.8. If the foIf the fork tips rk tips poinpoint dowt downwardnwards shis shims shoms should buld be adde added oved over the per the pressuressure plre plate (onate (on
the assumption that the forks are straight).the assumption that the forks are straight).
9.9. When When the fothe forks are rks are paraparallel, cllel, check heck the hthe heigheight. The t. The cylincylinders cders can be an be extenextended ded if it isif it is
not high enough.not high enough.
10.10. TTest lift, and cheest lift, and check that the ck that the straddle lift doestraddle lift does not lift skes not lift skeww. If so, adjus. If so, adjust the length oft the length of
the cylinders until the best lifting movement is obtained.the cylinders until the best lifting movement is obtained.
1111.. Check mCheck measueasure, and if nre, and if necesecessary maksary make furthe further adjuser adjustmentstments..
Figure 6.37Figure 6.37 Positioning of shimsPositioning of shims
06_011_A-Ergo_ShimH jSt.eps
06_011_A-Ergo_ShimH jSt.eps
To Next Page
Loading...