Why does the power indicator flash on and off on my ATP Electronics Security Sensors?
If the constant power indicator on your ATP Electronics Security Sensors flashes on and off, this indicates that the sensor may soon need replacing. You should obtain a replacement sensor, but you don't have to replace it until you receive a Failed Sensor Indication.
What to do if top 5 LEDs flash red and pump doesn't run on ATP Electronics Heated Pentode ZX-1A?
If the top 5 LEDs are flashing red and the pump isn't running on your ATP Electronics Security Sensors, this indicates a failed sensor. Replace the sensor.
How to fix erratic alarms in fresh air with ATP Electronics Security Sensors?
If your ATP Electronics Security Sensors unit behaves erratically, giving alarms in fresh air, it's likely due to a loose probe tip or flexible probe, which is disturbing the airflow. To resolve this, tighten the tip and/or probe.
What to do if the audible alarm doesn't sound on ATP Electronics Security Sensors?
If the audible alarm on your ATP Electronics Security Sensors doesn't sound even when the LEDs are lit, the MUTE feature might be engaged. De-activate the MUTE feature.
How to fix ATP Electronics Security Sensors when the power indicator LED doesn't light?
If the power indicator LED on your ATP Electronics Security Sensors does not light up and the unit doesn't switch on, it's likely because the batteries are not charged. Connect the charger to charge the batteries.
What does it mean when the charge indicator flashes red on ATP Electronics Heated Pentode ZX-1A during charging?
If, during battery charging, the charge indicator on your ATP Electronics Security Sensors begins to flash red, it indicates that the batteries have failed and cannot be recharged. Obtain a replacement battery pack.
Why does the charge indicator go out after 10 minutes when charging my ATP Electronics Heated Pentode ZX-1A?
If, during battery charging, the charge indicator goes out after 10 minutes on your ATP Electronics Security Sensors, it means the batteries have failed and cannot be recharged. Obtain a replacement battery pack.
Details the process of unpacking the leak detector unit and its components.
Provides instructions for installing the battery pack and charging the unit, including cautions.
Guide for installing the sensor and flexible probe onto the leak detector unit.
Explains the first LED as an intelligent battery status indicator with color coding.
Details how to display actual battery voltage using LEDs and their color meanings.
Describes the automatic circuit and reset function for ignoring ambient refrigerant and setting thresholds.
Explains how to adjust sensitivity between High and Low modes.
Details how the unit diagnoses and indicates sensor status, including 'Old Sensor' and 'Failed Sensor'.
Explains the dual alarm system and how to mute the audible alarm.
Describes how LEDs indicate leak size and concentration proportionally using color.
Details the recommended procedure for leak testing Automotive A/C Systems according to SAE J1628.
Provides techniques for effective leak detection, including probe inspection and refrigerant behavior.
Instructions for charging and maintaining batteries, including status indicators and temperature cautions.
Guidance on storing the unit for extended periods, including battery removal.
Information on proper disposal of Ni-MH batteries, emphasizing recyclability.
Details the Heated Pentode™ sensor as a consumable element and its eventual replacement.
Instructions for accessing, cleaning, and replacing the probe tip and filter cartridge.
Provides guidelines for general unit care, avoiding port obstruction and protecting the device.
Details the process of unpacking the leak detector unit and its components.
Provides instructions for installing the battery pack and charging the unit, including cautions.
Guide for installing the sensor and flexible probe onto the leak detector unit.
Explains the first LED as an intelligent battery status indicator with color coding.
Details how to display actual battery voltage using LEDs and their color meanings.
Describes the automatic circuit and reset function for ignoring ambient refrigerant and setting thresholds.
Explains how to adjust sensitivity between High and Low modes.
Details how the unit diagnoses and indicates sensor status, including 'Old Sensor' and 'Failed Sensor'.
Explains the dual alarm system and how to mute the audible alarm.
Describes how LEDs indicate leak size and concentration proportionally using color.
Details the recommended procedure for leak testing Automotive A/C Systems according to SAE J1628.
Provides techniques for effective leak detection, including probe inspection and refrigerant behavior.
Instructions for charging and maintaining batteries, including status indicators and temperature cautions.
Guidance on storing the unit for extended periods, including battery removal.
Information on proper disposal of Ni-MH batteries, emphasizing recyclability.
Details the Heated Pentode™ sensor as a consumable element and its eventual replacement.
Instructions for accessing, cleaning, and replacing the probe tip and filter cartridge.
Provides guidelines for general unit care, avoiding port obstruction and protecting the device.
General| Brand | ATP Electronics |
|---|---|
| Model | Heated Pentode ZX-1A |
| Category | Security Sensors |
| Language | English |
To Next Page
