Atron Systems Easy Weigh BX-120+ User Manual

BX-Series Checkweighing Floor Scale
Side A
TM
Installation & Assembly
Models &
Capacities
BX-120+ 120 x 0.02 lb
BX-150 150 x 0.05 lb
BX-300+ 300 x 0.05 lb
BX-300 300 x 0.1 lb
BX-600+ 600 x 0.1 lb
BX-600 600 x 0.2 lb
Pole & Display: Assembly of the pole display is required.
Please follow the Assembly Instructions on Side B:
1. Insert load cell cable through pole and insert pole
into the bottom bracket. Tighten all screws.
2. Attach the top bracket to the Display Head and feed
the load cell cable through the top bracket and
connect it to the back of the Display Head.
3. Tighten all screws and adjust the Display Head.
4. Remove the Lock Bolt from underneath the platform.
Initial Setup: Plug the AC adapter cable into the rear of
the display head and then the adapter into an AC outlet.
Some units have a fixed AC Cord instead of an adapter.
On/Off Key: The On/Off Key must be held down for
more than one second in order to turn the scale ON.
Operating the Scale
Make sure the platter is sitting properly on top of the
platform and that there is nothing on top of the platter.
Also, make sure that the scale is plugged into the proper
outlet. Hold down
until the scale display begins to
show the self test and then release the key. This is the
Initial State and displays appear like this:
The number of zeroes and decimal places may vary
depending on model and capacity.
Simple Weighing:
1. Place an item on the platter
2. The Stable Lamp will indicate a stable weight
3. Remove the item from the platter
Weighing Using Tares:
1. Place the empty container on the platter
2. Press
and then place an item on the platter
3. The Stable Lamp will indicate a stable weight
4. Remove the item from the platter
Once you press
, you will notice that the NET Lamp
will come on indicating to you that the weight shown is a
net weight. For example, this is what the display would
look like after you press
:
However, after Step 4 the display may look like this:
In this example, the platter is empty and the tare was set
using an empty container that weighs 2.50 pounds.
Clearing Tares:
1. Make sure that there is nothing on the platter
2. Press
and the display will show:
You are back to the Initial State.
Using the Unit Key:
1. Press
and the weighing units will change
2. Repeat Step 1 until you reach the units you desire*
You can use the
key in combination with/without tares
or with/without any weight on the platter. The scale offers
the following units: Pounds (lb), Ounces (oz), Kilograms,
(kg), Grams (g), Counting (Pcs), Percentage (%), and
Pound-Ounce (lb oz). *Note however that Counting,
Percentage, and Pound-Ounce are not to be used in Legal
for Trade applications.
Counting and Percentage Weighing:
1. Follow Unit key instructions to get to Pcs or % units
2. Press and hold down
until the display shows:
3. Release the
key. You can select to sample with
10, 20, 50, 100, or 500 pieces* by using the
key.
4. Place the indicated number of piece on the platter and
then press
. The scale will show Pcs or % values.
*Note that when using Percentage, the scale will sample
with 10, 20, 50, 100, or 500 %.
Using the Mode Key:
1. Press
and the weighing units will change
2. Repeat Step 1 until you reach the mode you desire*
You can use the
key in combination with/without tares
or with/without any weight on the platter. The scale offers
the following modes: Weighing1, Weighing2, Limit, and
Hold. *Note however that Weighing2 and Hold modes are
not to be used in Legal for Trade applications.
Charging the Battery
The
Lamp is located on the top left side of the display.
When it turns ON you need to recharge the battery. The
scale can be ON or OFF when recharging so long as it is
plugged into an AC outlet. The Recharge LED is located
above the
key and shows various states which are
explained on the other side of this guide. An overnight
charge of 12 hours, will yield approximately a 90% charge
or about 90 hours of continuous use (no-backlight.)

Atron Systems Easy Weigh BX-120+ Specifications

General

Brand	Atron Systems
Model	Easy Weigh BX-120+
Category	Scales
Language	English

Summary

Installation & Assembly

Pole & Display Assembly

Guides assembly of the pole and display unit for the scale, including connecting components.

Initial Setup and Powering On

Details initial setup steps, including power connection and turning the scale on.

Using the On/Off Key

Explains the procedure for turning the scale on and off, requiring a press-and-hold action.

Operating the Scale

Simple Weighing Procedure

Instructions for basic weighing without tares, including placing items and observing stability.

Weighing Using Tares

How to use the tare function for weighing with containers, showing net weight indication.

Clearing Tares

Steps to reset the tare function and return the scale display to zero.

Using the Unit Key

Counting and Percentage Weighing

Using the UNIT key for specific weighing modes like counting pieces or calculating percentages.

Using the Mode Key

Selecting Weighing Modes

How to select different operating modes like Weighing, Limit, or Hold.

Charging the Battery

Battery Recharge Indicator

Information on recharging the scale's battery and understanding the charge status indicators.

Nomenclature & Pole Assembly

Component Identification

Identifies key parts of the scale, including the pole, display head, and load cell cable.

Pole Assembly Steps

Detailed steps for assembling the scale's pole and attaching it to the display head.

Recharge LED Indicators

Understanding Charging States

Explains the meaning of different LED colors (Green, Yellow, Red, Off) during battery charging.

Keypad Functions

Key Descriptions

Details the function of each key on the scale's control panel, such as G/N/T, UNIT, MODE, TARE, ZERO.

Display Indicators

Interpreting Display Symbols

Explains the meaning of various indicators and symbols shown on the scale's display.

Backlight Settings

Adjusting Display Backlight

Instructions on how to adjust or set the display backlight to on, off, or auto.

Auto Shutoff Configuration

Setting Auto Shutoff Timer

Configuration options for the automatic power-off feature, allowing selection of time intervals.

Error Messages and Solutions

Err 4: Zeroing Capacity Exceeded

Addresses errors related to exceeding the zeroing capacity, suggesting weight removal.

Err 5: Keyboard Error

Describes keyboard errors, indicating a potential keypad malfunction requiring replacement.

Err 6: Load Cell Error

Relates to load cell errors, suggesting checking the load cell cable connection.

Technical Specifications

Scale Model Details

Lists technical details, capacities, resolutions, dimensions, and power requirements for scale models.