EasyManua.ls Logo

ATS HGO 40 - User Manual

Default Icon
48 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Instrukcja oryginalna 2017
Instrukcja obsługi
/Dokumentacja techniczno-ruchowa/
Osuszaczy adsorpcyjnych ATS
HGO/HGL 40-160
Upoważniony przedstawiciel:
FACHOWIEC F.H.W.
Zenon Świętek
ul. Stefańskiego 29,
61-415 Poznań.
Producent:
ATS S.r.l.
Via Enzo Ferrari 4
37045 – S. Pietro di Legnago (Verona) - Italy
Sprzedaż hurtowa,
detaliczna, serwis.
ul. Grunwaldzka 390,
60-169 Poznań.
tel. 061 66 18 159,
fax 061 66 18 156
www.fachowiec.com
Przed użyciem należy przeczytać dokładnie i ze zrozumieniem instrukcję obsługi.
Należy stosować środki ochrony oczu i twarzy.
Należy stosować środki ochrony dłoni.
Należy stosować ochronny kombinezon roboczy.
Należy stosować środki ochrony słuchu.

Table of Contents

Questions and Answers

  • T
    Timothy ScottAug 7, 2025
    Why is the dew point high in my ATS Dehumidifier?
    • L
      lopezjohnAug 7, 2025
      A high dew point in your ATS Dehumidifier can be caused by several factors. The inlet temperature may be above the design condition, so you should check the aftercooler or compressor. Water might be entering the desiccant bed; in this case, check the air/moisture separator and prefilter, and replace the desiccant if needed. The desiccant could also be contaminated by oil, so install a suitable prefilter and replace the desiccant if necessary. Finally, an insufficient purge rate could be the culprit, so check the muffler.
  • K
    Kevin JohnsonAug 11, 2025
    What to do if my ATS HGO 40 fails to shift towers from drying to regenerating service?
    • M
      mlewisAug 12, 2025
      If your ATS Dehumidifier isn't shifting towers, it could be due to several reasons. First, check the output voltage to the solenoid valve to ensure there is input power. Next, verify the input voltage to the solenoid valve, as the solenoid valve itself may be faulty. Lastly, the timing on the dryer might be off, so inspect the controller.
  • A
    Ariel GriffithAug 16, 2025
    Why is there an excessive pressure drop in my ATS Dehumidifier?
    • R
      robinschultzAug 16, 2025
      An excessive pressure drop in your ATS Dehumidifier can occur due to an excessive flow rate, so check the flow rate. It can also happen if the inlet pressure is under the design condition, so verify the pressure source.
  • L
    Lisa JenkinsAug 20, 2025
    What causes high pressure in the regenerating tower of my ATS HGO 40 Dehumidifier?
    • J
      Jessica ColonAug 20, 2025
      High pressure in the regenerating tower (above 1 bar) of your ATS Dehumidifier may be due to a clogged muffler. Additionally, the outlet check valve might be staying open; in this case, clean and/or replace it.
  • D
    Danielle ThompsonAug 25, 2025
    What causes my ATS HGO 40 to depressurize too rapidly?
    • M
      mary99Aug 26, 2025
      If your ATS Dehumidifier depressurizes too rapidly, the purge valve may not be closing properly. Check the solenoid valve and repair or replace it if necessary.
  • D
    davidromeroAug 29, 2025
    How to troubleshoot if my ATS Dehumidifier fails to purge?
    • B
      Brittany DavenportAug 29, 2025
      If your ATS Dehumidifier fails to purge, it could be because the purge valve does not open. Check the solenoid valve, and repair or replace it if necessary. Another possible cause is a clogged purge muffler.
  • M
    Michael JohnsonSep 2, 2025
    Why my ATS HGO 40 Dehumidifier fails to pressurize?
    • A
      Angela MillerSep 2, 2025
      If your ATS Dehumidifier fails to pressurize, it might be due to a faulty purge valve. Check the purge valve and the timer sequencing.

ATS HGO 40 Specifications

General IconGeneral
BrandATS
ModelHGO 40
CategoryDehumidifier
LanguageEnglish