Attwood 5091 - User Manual

12-Volt 1-Mile
Bi-Color Pole Lights
5091, 5092
Installation Instructions
Attwood marine hardware, navigational lighting, bilge pumps, and
other marine accessories are specified more than any other brand by
America’s best-known boat manufacturers as original equipment.
Look to Attwood for quality replacement parts and marine accessories.
SAVE THESE INSTRUCTIONS
Form Number 69381 Rev. B 03-10
3
®
INSTALLATION
Pole Light
CAUTION:
All positive (+12V DC) wires must be fused to protect your circuits
and vessel. The Universal Fit Light requires a 1-amp fuse. The
aluminum pole of the Universal Fit Light is not connected to an
electrical ground.
Replacing a Light Without a Locking Collar
1. Insert pole into base, aligning screws with slot in base.
2. Press down firmly to engage electrical connectors.
3. Lock pole in position with lock mechanism of base.
4. To remove light, unlock pole from base and pull straight up.
(Figure 2)
Replacing a Light With a Locking Collar
1. Remove both screws from base end of pole.
2. Slide plastic locking collar supplied with Universal Fit Light up over
terminal connector and past screw holes on pole.
3. Replace screw closest to base end of pole only.
4. Insert pole into base, aligning screw with slot in base.
5. Press down firmly to engage electrical connectors.
6. Slide locking collar down to base, rotate until lower ring can be
inserted inside top of base.
7. Press down into base and rotate until locking collar tightens
between pole and base.
NOTE:
Periodically check pole to make sure it is secure.
8. To remove light, rotate locking collar in opposite direction until it
loosens, then pull up on pole. (Figure 3)
After installation, activate lights to verify proper operation. Navigation
light regulations require lights to be operated with a three-position
switch that provides for:
• Running lights (sidelights and all-round light).
• Anchor lights (all-round light only).
• Off.
Figure 2
FEATURES
The new Attwood 12-Volt, 1-Mile Navigation Sidelights for boats
up to 39.6 ft. (12 meters). They feature impact resistant, UV-stable
polycarbonate housings. The lens completely encapsulates the bulb
and socket assembly for a splash resistant seal. Meets USCG CFR
183.810, ABYC A-16 requirements, and all applicable standards as
tested by Imanna Labs, 3/31/1997. 1 Nautical Mile visibility. Uses
Lamp 9235, #906 13V, 6 Candle Power.
REQUIRED FOR INSTALLATION
• Cordless drill with 1/8" (3mm), 3/8" (10mm) and 3/4" (19mm) bits.
• Screwdriver.
• Two #8 or #10 stainless pan head screws per light.
• Non-silicone sealant.
WARNING:
To prevent personal injury, always disconnect the power source
when installing or servicing this product. Always remove the boat
from
the water before using 120V AC power tools.
LOCATION
Lights must be mounted so that the light pattern is unobstructed.
Locate Bi-Color combination light in an area as far forward as
possible. (Figure 1)
Figure 1
Green
(Starboard)
Red
(Port)

Summary

Product Installation

Installing Pole Light

Connect +12V DC wires, fused for circuit protection, to the Universal Fit Light's 1-amp fuse.

Replacing Light with Locking Collar

Remove base screws, slide locking collar up, and align with slots on pole.

Product Maintenance

Replacing Light Bulb

Unscrew lens helmet, replace bulb with 9-Watt Wedge Base, screw helmet back on until it clicks.

Attwood Limited Warranty

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Installation (Pole Light)
5. Replacing a Light Without a Locking Collar
6. Replacing a Light With a Locking Collar
7. Storage
8. Maintenance Features
9. Replacing Bulb
10. Cleaning
11. Warranty Information

The Attwood 12-Volt, 1-Mile Bi-Color Pole Lights (models 5091, 5092) are navigational sidelights designed for boats up to 39.6 feet (12 meters) in length. These lights are a crucial component for marine safety, ensuring visibility and compliance with maritime regulations. Attwood is a trusted brand, with its marine hardware, navigational lighting, bilge pumps, and other accessories frequently specified as original equipment by leading boat manufacturers in America.

Function Description:

The primary function of these pole lights is to provide navigation sidelights for boats, indicating the vessel's presence and direction to other watercraft. The bi-color design features a red light for the port (left) side and a green light for the starboard (right) side, mounted in an area as far forward as possible on the boat to ensure an unobstructed light pattern. This configuration is essential for meeting navigation light regulations, which require lights to be operated with a three-position switch providing for:

• Running lights (sidelights and all-round light)
• Anchor lights (all-round light only)
• Off

Important Technical Specifications:

• Voltage: 12-Volt DC.
• Visibility: 1 Nautical Mile.
• Boat Length Compatibility: Up to 39.6 feet (12 meters).
• Lamp Type: Uses Lamp 9235, #906 13V, 6 Candle Power.
• Housing Material: Impact-resistant, UV-stable polycarbonate housings.
• Seal: The lens completely encapsulates the bulb and socket assembly, providing a splash-resistant seal.
• Fuse Requirement: The Universal Fit Light requires a 1-amp fuse.
• Electrical Grounding: The aluminum pole of the Universal Fit Light is not connected to an electrical ground.
• Compliance: Meets USCG CFR 183.810 and ABYC A-16 requirements, as tested by Imanna Labs on 3/31/1997.

Usage Features:

Installation (Pole Light):

• Required Tools: Cordless drill with 1/8" (3mm), 3/8" (10mm), and 3/4" (19mm) bits; screwdriver; two #8 or #10 stainless pan head screws per light; non-silicone sealant.
• Safety Precaution: Always disconnect the power source when installing or servicing to prevent personal injury. Remove the boat from the water before using 120V AC power tools.
• Wiring: All positive (+12V DC) wires must be fused to protect circuits and the vessel.
• Location: Lights must be mounted to ensure an unobstructed light pattern, ideally as far forward as possible.

Replacing a Light Without a Locking Collar:

1. Insert the pole into the base, aligning screws with the slot in the base.
2. Press down firmly to engage electrical connectors.
3. Lock the pole in position with the base's lock mechanism.
4. To remove, unlock the pole from the base and pull straight up.

Replacing a Light With a Locking Collar:

1. Remove both screws from the base end of the pole.
2. Slide the plastic locking collar (supplied with the Universal Fit Light) up over the terminal connector and past the screw holes on the pole.
3. Replace only the screw closest to the base end of the pole.
4. Insert the pole into the base, aligning the screw with the slot in the base.
5. Press down firmly to engage electrical connectors.
6. Slide the locking collar down to the base, rotate until the lower ring can be inserted inside the top of the base.
7. Press down into the base and rotate until the locking collar tightens between the pole and the base.
   • Note: Periodically check the pole to ensure it is secure.
8. To remove, rotate the locking collar in the opposite direction until it loosens, then pull up on the pole.

Storage:

• When not in use, always store the pole light in Pole Light Storage Clips (Attwood 7571).
• Choose a storage location where the light will not be damaged or be in constant contact with water.
• Close the base cover when the light is stowed to protect the contacts and seal the deck.
• Note: Navigation light poles are designed to support only the light; they should never be used as flag poles or handles.

Maintenance Features:

Replacing Bulb:

1. Unscrew the lens helmet counter-clockwise and remove it from the pole.
2. Replace the bulb with a 9-Watt Wedge Base Replacement Bulb (Attwood 9235).
3. Screw the lens helmet clockwise onto the pole until it clicks.

Cleaning:

• Clean the light with a mild soap and warm water solution.
• Caution: Never use solvents or abrasives, as they may damage the lens or housing of the Universal Fit Light.

Warranty Information:

Attwood provides a limited warranty for products used on pleasure boats. This warranty does not cover damage due to accident, improper installation, unreasonable or improper use, lack of proper maintenance, unauthorized repairs or modifications, normal wear and tear, or other causes not arising from defects in materials or workmanship. The warranty is limited to repair or replacement at Attwood's option, without expense to the original consumer purchaser. Expenses for removal, reinstallation, or transportation are not covered. Products must be returned to Attwood's plant, postage prepaid, with proof of original purchase. If repair or replacement is not commercially practical, Attwood may refund the purchase price, less depreciation. This warranty is Attwood's only express warranty; no implied warranty extends beyond one (1) year from the date of original consumer purchase. Attwood is not liable for damages for loss of use, incidental, or consequential damages, costs, or expenses. Some states may not allow limitations on implied warranties or exclusions of incidental/consequential damages, so these limitations may not apply to all consumers. This warranty provides specific legal rights, and other rights may vary by state.

Attwood 5091 Specifications

General

Brand	Attwood
Model	5091
Category	Boating Equipment
Language	English