To Next PageTo Next PageWhy is my ATVEL Vacuum Cleaner losing suction?
If your ATVEL Vacuum Cleaner is losing suction, it might be due to a blocked HEPA filter. Please check and clean the HEPA filter. Also, a wet HEPA filter can cause this issue, so ensure you dry the HEPA filter thoroughly before use. Additionally, check that the scraper is correctly installed; if not, reinstall it.
How to fix ATVEL Vacuum Cleaner not charging?
If your ATVEL Vacuum Cleaner isn't charging, first check the power supply connection to ensure it's well connected. Also, make sure the cleaner is properly placed on the charging station; if not, replace the cleaner on the charging station.
What to do if my ATVEL Ultimate F16 doesn't work in self-cleaning mode?
If your ATVEL Vacuum Cleaner isn't working in self-cleaning mode, ensure it's properly connected to the power supply. Also, empty the dirty water tank if it's full. Additionally, make sure the clean water tank is filled. If the issue persists, calibrate the vacuum cleaner.
Why is my ATVEL Ultimate F16 Vacuum Cleaner clean water tank leaking?
If the clean water tank of your ATVEL Vacuum Cleaner is leaking, it could be due to several reasons. First, if the water volume is higher than the snuffle valve, pour out water until it's below the valve. Second, ensure the clean water tank is correctly installed. Lastly, check that the cap is screwed on tightly.
Why is there no water coming out when spraying with my ATVEL Ultimate F16?
If no water comes out when spraying with your ATVEL Vacuum Cleaner, first ensure that the clean water tank is full. If it is, then check if the clean water tank is installed correctly; if not, please reinstall it.
Why does my ATVEL Ultimate F16 sewage tank prompts full water alarm even if it is not full?
If your ATVEL Vacuum Cleaner prompts a full water alarm even when the sewage tank isn't full, the filter or HEPA might be clogged. Clean the dirty filters or HEPA. Also, if the HEPA is too wet, dry it before use.
Why is my ATVEL Ultimate F16 Vacuum Cleaner handle control not working?
If the handle control on your ATVEL Vacuum Cleaner isn't working, the battery capacity might be low, so check the battery capacity and fully charge it. Alternatively, the handle might not be connected properly, so try reinstalling the handle.
Why does my ATVEL Ultimate F16 Vacuum Cleaner have water drops at the air outlet?
If you notice water drops at the air outlet of your ATVEL Vacuum Cleaner, it might be because the HEPA filter isn't installed. Check and install the HEPA filter. Also, avoid tilting the cleaner too much during use. Finally, if you've vacuumed foam liquid, empty the dirty water tank promptly.
Why is my ATVEL Ultimate F16 indicator display of clean water tank incorrect?
If the indicator display of the clean water tank on your ATVEL Vacuum Cleaner is incorrect, it might need calibration. To calibrate, take off the Clean Water tank, then start to clean and spray, turn cleaner off until draining the pipe. Then press the 'Switch Button' and 'Eco/Max Button' for 5 seconds until the digital display flashes two times.
Why does my ATVEL Ultimate F16 Vacuum Cleaner move hard?
If your ATVEL Vacuum Cleaner moves with difficulty, the roller brush might not be installed correctly. Check and reinstall the Roller Brush as guided.
Step-by-step guide for assembling the vacuum cleaner.
Instructions for filling the clean water tank with water or cleaning solution.
Steps for charging the vacuum cleaner and its battery pack.
How to operate the vacuum cleaner for effective floor cleaning.
Guide for cleaning and maintaining the roller brush.
Steps for emptying and cleaning the dirty water tank.
Instructions for cleaning the charging base.
Recommendations for storing the vacuum cleaner and its parts.
General| Battery Capacity | 2500 mAh |
|---|---|
| Charging Time | 4-5 hours |
| Dustbin Capacity | 0.6 L |
| Weight | 6.28 lbs |
| Dust Capacity | 0.6 L |
| Filters | HEPA |
| Type | Cordless |
| Noise Level | 72 dB |
