Audio enhancement K-SRC14 - Command List

29
Rev.2.10
Command List
Command
Content
Type
1st parameter
2nd parameter
Command example
QPW
Query about this
unit power state
Query
None
None
$QPW[CR][LF]
Response
1: POWER ON
None
$QPW:1[CR][LF]
CCS
Notification of
microphone power
state
Change
notification
1: MIC1 input
2: MIC2 input
0: MIC OFF
1: MIC ON
$CCS:1:1[CR][LF]
QCS
Query about
microphone power
state
Query
1: MIC1 input
2: MIC2 input
None
$QCS:1[CR][LF]
Response
Same as above
0: MIC OFF
1: MIC ON
$QCS:1:0[CR][LF]
SVL
Volume setting
Setting
1: MIC1 input
2: MIC2 input
L: LINE input
* Refer to
“Volume list”
(page 32).
$SVL:L:00[CR][LF]
Response
Same as above
Same as above
$SVL:L:00[CR][LF]
SVU
Volume 1-step up
Setting
1: MIC1 input
2: MIC2 input
L: LINE input
None
$SVU:1[CR][LF]
Response
Same as above
None
$SVU:1[CR][LF]
SVD
Volume 1-step
down
Setting
1: MIC1 input
2: MIC2 input
L: LINE input
None
$SVD:2[CR][LF]
Response
Same as above
None
$SVD:2[CR][LF]
QVL
Volume query
Query
1: MIC1 input
2: MIC2 input
L: LINE input
None
$QVL:1[CR][LF]
Response
Same as above
* Refer to
“Volume
list” (page 32).
$QVL:1:01[CR][LF]
SMT
Mute individual
setting
Setting
1: MIC1 output
2: MIC2 output
M: MIX output
0: MUTE OFF
1: MUTE ON
$SMT:1:0[CR][LF]
Response
Same as above
Same as above
$SMT:1:0[CR][LF]
QMT
Mute state query
Query
1: MIC1 output
2: MIC2 output
M: MIX output
Same as above
$QMT:M[CR][LF]
Response
Same as above
0: MUTE OFF
1: MUTE ON
$QMT:M:0[CR][LF]
SAM
Mute collective setting
Setting
0: MUTE OFF
1: MUTE ON
None
$SAM:1[CR][LF]
Response
Same as above
None
$SAM:1[CR][LF]
CPM
Notification of
page mute state
Change
notification
0:PAGE MUTE OFF
1:PAGE MUTE ON
None
$CPM:1[CR][LF]
QPM
Query about page
mute state
Query
None
None
$QPM[CR][LF]
Response
0:PAGE MUTE OFF
1:PAGE MUTE ON
$QPM:0[CR][LF]
CF1
Notification of E1sta
Change
notification
None
None
$CF1[CR][LF]
CF2
Notification of E2
state
* 3-time transmission
at 1 sec. interval
Change
notification
0: Non E2 status
1: E2 status & E2 ACK
signal not received
2: E2 status & E2 ACK
signal received
None
$CF2:1[CR][LF]
QF2
Query about E2
state
Query
None
None
$QF2[CR][LF]
Response
0: Non E2 status
1: E2 status & E2 ACK
signal not received
2: E2 status & E2 ACK
signal received
None
$QF2:2[CR][LF]
SDS
Microphone
override setting
Setting
1: Microphone
Override
0: Disable
1: Enable
$SDS:1:0[CR][LF]
Response
Same as above
Same as above
$SDS:1:0[CR][LF]