Autopilot ChlorSync User Manual

Level Min. Max.
Salt
Ideal3,500ppm(mg/L)
2,700ppm(mg/L) 5,000ppm(mg/L)
WaterFlow
20gpm(4.5m
3
/hr.) 80gpm(18.2m
3
/hr.)
ModelOutput Production/Day
CS30 1.1lbs/0.50kg
CS40 1.4lbs/0.64kg
CS50 1.7lbs/0.77kg
Status Display Indication
Chlorine
Generating
Status
SaltLEDIndicator:
On(solid) Normal SaltLevel=2,700‐5,000ppm(mg/L)‐Recommended ON
Flashing Normal SaltLevel>5,000ppm(mg/L)‐HighSalt ON
On(solid) LoSALt SaltLevel=2,300‐2,700ppm(mg/L)‐LowSalt ON
Flashing AddSALt SaltLevel<2,300ppm(mg/L)‐SaltAdditionRequired OFF
On(solid) Normal NormalOperation ON
Flashing
CLnCELLorCLnCELL
SOOn
LowConductivity/HighCurrent(Scale
formation,LowSalt,
Etc.)orOpenCell
OFF
On(solid) Normal Normalwaterflowdetected ON
Flashing noFLo LoworNoWaterFlowdetected OFF
‐Cellsize[CS30,CS40,orCS50]
‐WaterTemerature[F.°]
‐SaltConcentration[ppm]
‐CurrentandVoltage
ImmediateSaltCheck(withPoo lSync®):
1.OpentheappandselecttheChlorSyncundertheEQUIPMENT 
options
2.Pressthe3‐dotmenuontheChlorSyncpage
3.SelectSALT,apop‐upwindowwillprompttoREMEASURESALT.
4.SelectOk.
Notes:
֎Thedisplayedsaltlevelisupdatedasfollows
‐Whenthepowerisrestoredorwhenflowisestablished
‐Every12hoursafterpowerisappliedorflowisestablishedifsaltlevelsareabove2,300ppm(mg/L).
‐Every60minutesifsaltlevelis<2,300ppm(mg/L)
INDICATORLIGHTS
Color
Green
Green
Red
Red
RISKOFELECTRICALSHOCK‐Allelectricalconnectionsshouldbemadebyalicensedelectricianorcertifiedelectricalcontractor.
Connecting230Vactoaunitthathasbeenconfiguredto110‐120Vacwillresultinpermanentdamagetotheunit.Damageduetoincorrect
wiringisnotcoveredunder
thewarranty.
Warning‐Failuretoheedthefollowingmayresultinpermanentinjuryordeath.
Caution‐Failuretoheedthefollowingmayresultinequipmentdamage.
RISKOFELECTRICALSHOCK‐DisconnectallACpowerwheninstallingorservicingthissystem.Followallstate,local,andNationalElectrical
Code(s)(provincialandCanadianElectrical
Code(s)ifapplicable).Usecopperconductorsonly.
RISKOFELECTRICALSHOCK‐Beforepluggingorunpluggingtheunittothepowercenter,firstswitchofftheACpowertothepowercenter.
֎Aerthepurifieroutputlevelissetusingthearrowbuons,theunitwillautomacally
makefineoutputadjustmentsasthewatertemperature
fluctuates.Thispatentedtemperaturecompensationfeaturewilladjustoutputdependingonwatertemperature.
ChlorSync®‐TroubleshootingGuide
Ratedat3,500ppmsalt
֎Whenthewatertemperaturefallsbelow55°F(12.8°C),chlorineproduconisreducedto1%topreventoverchlorinaon.Normalproduconwill
resumewhenthewatertemperaturerisesabovethislevel.
Red
CellLEDIndicator:
Green
Red
FlowLEDIndicator:
Allcellsdraw6.5‐7.5amps
Green
ManualReadings(noPoolSync®):PresstheUpArrow 5times,thenpresstheDownArrow 5times.
Thefollowingwillbedisplayed
Forfullmanualuse
QRcode
LTM1034
1of2

Autopilot ChlorSync Specifications

General

Brand	Autopilot
Model	ChlorSync
Category	Swimming Pool Filter
Language	English