AXE MM2 Series - Advanced Operation Settings; Alarm Hysteresis and Delay Settings; Analog Output and Communication Setup; Alarm Value Configuration


5-3 ACT1(Alarm Active 3
setting page )Default=HI

1.Decide active 3 with  or  key(HI or LO)
2.Press  key enter data and into ACT4 setting page

5-4 ACT2(Alarm Active 4
setting page )Default=HI

1.Decide active 4 with  or  key(HI or LO)
2.Press  key enter data and into HYS1 setting page
 5-5 HYS1(Alarm Hysteresis 1
setting page)Default=0

1.Decide Hysteresis 1 with  or  or  key(0~999)
2.Press  key enter data and into HYS2 setting page
 5-6 HYS2(Alarm Hysteresis 2
setting page)Default=0

1.Decide Hysteresis 2 with  or  or  key(0~999)
2.Press  key enter data and into HYS3 setting page

5-7 HYS3(Alarm Hysteresis 3
setting page)Default=0

1.Decide Hysteresis 3 with  or  or  key(0~999)
2.Press  key enter data and into HYS4 setting page

5-8 HYS4(Alarm Hysteresis 4
setting page)Default=0

1.Decide Hysteresis 4 with  or  or  key(0~999)
2.Press  key enter data and into DEL1 setting page
 5-9 DEL1(Alarm Delay 1
setting page)Default=0

1.Decide delay 1 with  or  or  key(0~99.9 sec)
2.Press  key enter data and into DEL2 setting page
 5-10 DEL2(Alarm Delay 2
setting page)Default=0

1.Decide delay 2 with  or  or  key(0~99.9sec)
2.Press  key enter data and into DEL3 setting page

5-11 DEL3(Alarm Delay 3
setting page)Default=0

1.Decide delay 3 with  or  or  key(0~99.9 sec)
2.Press  key enter data and into DEL4 setting page

5-12 DEL4(Alarm Delay 4
setting page)Default=0

1.Decide delay 4 with  or  or  key(0~99.9sec)
2.Press  key enter data and into SB setting page
 5-13 SB(Start band)
Default=0

1.Decide start band with  or  or  key(-999~999)
2.Press  key enter data and into SDT setting page
 5-14 SDT(Start Delay Time)
Default=0

1.Decide start delay time with  or  or  key(0~99.9sec)
2.Press  key enter data and return ROP setting group
6
AOP(Analog output setting
group)

Press  key decide AOP setting group , press 
key into
ANLO setting page
 6-1
ANLO(A/O Zero According
to Display setting
page)Default=0

1.Decide ANLO with  or  or  key(-19999~19999)
2.Press  key enter data and into ANHI setting page
 6-2
ANHI(A/ O Span According
to Display setting
page)Default=0

1.Decide ANHI with  or  or  key(-19999~19999)
2.Press  key enter data and return AOP setting group
7
DOP(Communication
setting group)

press  key decide DOP setting group,press  key into
ADDR setting page
 7-1
ADDR(Communication – Addr
ess setting page )
Default=0

1.Decide address with  or  or  key(0~255)
2.Press  key enter data and into BAUD setting page
 7-2
BAUD(Communication Baud
Rate setting page)Value
on Default=19200

1.Decide baud rate with  or  key(19200,9600,4800,2400)
2.Press  key enter data and into PARI setting page
 7-3
PARI(Communication
Parity Check setting
page)Default=n82

1.Decide parity check with  or  key(n82,n81,even,odd)
2.Press  key enter data and return DOP setting group
Step Parameter mark description Parameter mark Operation manual
8 Normal display  Press  /ALARM key about 3 sec,into AL1 setting page
 8-1
AL1 (Alarm value 1 setting
page) Default=0

1.Decide alarm value 1 with  or  or  key(-19999~19999)
2.Press  key enter data and into AL2 setting page
 8-2 AL2 (Ala
rm value 2 setting
page) Default=0

1.Decide alarm value 2 with  or  or  key(-19999~19999)
2.Press  key enter data and into AL3 setting page

8-3
AL3 (Alarm value 3 setting
page) Default=0

1.Decide alarm value 3 with  or  or  key(-19999~19999)
2.Press  key enter data and into AL4 setting page

8-4
AL4 (Alarm value 4 setting
page) Default=0

1.Decide alarm value 4 with  or  or  key(-19999~19999)
2.Press  key enter data and return normal display