FEATURES & COMPONENTS
1. Night-Vision LED
2. Lens
3. Microphone
4. Power On/Off
5. Power Indicator
6. Speaker
7. Temperature Sensor
8. DC Jack
9. Wall Mounng Hole
10. Adapter
THIS PRODUCT CAN NOT SUBSTITUE PARENT’S SUPERVISION ON YOUR CHILD.
WARNING
- Store this product out of the reach of babies (at least 3 feets (0.9 m) away from the crib). A strap
wound around the baby’s neck may result in asphyxiaon. Use a safety clip to clamp the power cord
and keep it out of baby’s reach. Do not use other extension cords. Only use the power adapter
provided.
- Do not touch the exposed part if the adapter is connected with power.
- Test regularly before inial use or when change the posion of camera.
- Avoid placing the product in humid place or contacng with liquid. (such as bathtub, sink, etc.)
- Do not apply heat to the product.(such as stoves, radiators, etc.)
- Using the product in venlated place. Avoid placing it on sofas, cushions, beds or other places which
may block venlaon.
- The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are
contained, please be careful when unpack and install it.
keep the distance
between sensor and body
at least 0.6 inch for
accurate temperature
result
0.6 in
SETUP & USE
3 feet
Figure 1
3 feet
Figure 2
*Up To 2 Cameras:
One monitor can be extended to
two cameras at most.
WARNING
Asphyxiaon Danger: Store this product out of the reach of babies (at least
3 feet away from the crib). A strap wound around the baby’s neck may result in
asphyxiaon. Use a safety clip to clamp the power cord and keep it out of baby’s
reach. Do not use other extension cords. Only use the power adapter provided.
Step 1: Test recepon first, put the camera in a suitable place that will
provide you the best view of your baby in the crib (Note: Do not hang up
the camera firmly unl the inial installaon test is completed). Plug the
adapter into the wall outlet and turn on the camera.
Step 2: Turn on the monitor by pressing and holding the Power / Video
buon for 5 seconds unl “axvue” shows up, then the video will show up
on the screen immediately. If the video does not show up, please refer to
“TO PAIR MONITOR AND CAMERA (ADD CAMERA)” on the next page. If
the video shows up, the inial installaon test is completed, then you can
set up the camera according to the instrucon below.
Set Up Camera: Place the camera on a flat surface, such as a wardrobe or
shelf (Figure 1). Or hang it on the wall (Figure 2). No maer wherever to
place the camera, please make sure to keep it away from the crib for at
least 3 feet and all power cords should be placed behind the camera
properly. Then adjust the angle of the camera lens unl the enre crib
shows up on the display, or adjust it to the best angle that you think to
watch your baby.
Please charge the battery for at least 8 hours before using the product.
Step 1: Place the monitor display in the living room, bedroom or any place you want to watch your
baby. Use an adapter to connect the camera with an electrical outlet.
Step 2: Turn on the monitor by pressing the Power / Video“ ” buon for 5 seconds unl axvue logo
or video shows up on the screen.
Step 3: Press Power / Video“ ” buon to turn off the video if you only need to hear the voice.
Step 4: Turn off the monitor completely by pressing and holding the Power / Video“ ” buon for
5 seconds.
TO USE PLUGGED-IN MODE
Get to know us at: www.axvue.com
Please read the following instrucons and warnings carefully
Keep this instrucon manual for future.
For adult use only.
INSTRUCTION MANUAL
Model - A1080PT
Revised at 10/2020
AXVUE A1080PT Extra Camera
For A1080P/E1080P
To Next Page
Need help?
General