Axxess AX-ADCT2 User Manual

AX-ADCT2
AX-ADCT2
AX-ADCT2
AX-ADCT2
AX-ADCT2
AX-ADCT2
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
The AX-ADCT2 should be installed on a stereo’s speaker
output wires or the output wires on an OEM amplier of up to 80
watts per channel. These wires can be found behind the stereo
in the dash, on the outside of an OEM amplier, or on the input
terminals on the OEM speakers.
Wire Color & Function:
The audio input wire colors are an EIA
standard for car stereo applications as follows:
YELLOW = BATTERY +12V Input
BLACK = GROUND Input
BLUE = REMOTE +12V Output
THE ABOVE POWER WIRES CAN BE CONNECTED DI-
RECTLY TO THE AMPLIFIER BEING ADDED
WHITE = LEFT Front (+) Input
WHITE/BLACK = LEFT Front (-) Input
GRAY = RIGHT Front (+) Input
GRAY/BLACK = RIGHT Front (-) Input
BLACK/WHITE = Reference Ground (-) (REFERENCE
GROUND OPTIONAL IF NOISE IS PRESENT)
NOTE: Be sure that all audio input connections are polarized or
in phase with each other. That is, the positive output wires from
the audio source need to be connected to the corresponding
positive input wires of the AX-ADCT2. The same goes for the
negative audio wires. Failure to do this will result in poor bass
response and low quality audio.
The AX-ADCT2 should be installed on a stereo’s speaker
output wires or the output wires on an OEM amplier of up to 80
watts per channel. These wires can be found behind the stereo
in the dash, on the outside of an OEM amplier, or on the input
terminals on the OEM speakers.
Wire Color & Function: The audio input wire colors are an EIA
standard for car stereo applications as follows:
YELLOW = BATTERY +12V Input
BLACK = GROUND Input
BLUE = REMOTE +12V Output
THE ABOVE POWER WIRES CAN BE CONNECTED DI-
RECTLY TO THE AMPLIFIER BEING ADDED
WHITE = LEFT Front (+) Input
WHITE/BLACK = LEFT Front (-) Input
GRAY = RIGHT Front (+) Input
GRAY/BLACK = RIGHT Front (-) Input
BLACK/WHITE = Reference Ground (-) (REFERENCE
GROUND OPTIONAL IF NOISE IS PRESENT)
NOTE: Be sure that all audio input connections are polarized or
in phase with each other. That is, the positive output wires from
the audio source need to be connected to the corresponding
positive input wires of the AX-ADCT2. The same goes for the
negative audio wires. Failure to do this will result in poor bass
response and low quality audio.
The AX-ADCT2 should be installed on a stereo’s speaker
output wires or the output wires on an OEM amplier of up to 80
watts per channel. These wires can be found behind the stereo
in the dash, on the outside of an OEM amplier, or on the input
terminals on the OEM speakers.
Wire Color & Function: The audio input wire colors are an EIA
standard for car stereo applications as follows:
YELLOW = BATTERY +12V Input
BLACK = GROUND Input
BLUE = REMOTE +12V Output
THE ABOVE POWER WIRES CAN BE CONNECTED DI-
RECTLY TO THE AMPLIFIER BEING ADDED
WHITE = LEFT Front (+) Input
WHITE/BLACK = LEFT Front (-) Input
GRAY = RIGHT Front (+) Input
GRAY/BLACK = RIGHT Front (-) Input
BLACK/WHITE = Reference Ground (-) (REFERENCE
GROUND OPTIONAL IF NOISE IS PRESENT)
NOTE: Be sure that all audio input connections are polarized or
in phase with each other. That is, the positive output wires from
the audio source need to be connected to the corresponding
positive input wires of the AX-ADCT2. The same goes for the
negative audio wires. Failure to do this will result in poor bass
response and low quality audio.
The AX-ADCT2 should be installed on a stereo’s speaker
output wires or the output wires on an OEM amplier of up to 80
watts per channel. These wires can be found behind the stereo
in the dash, on the outside of an OEM amplier, or on the input
terminals on the OEM speakers.
Wire Color & Function: The audio input wire colors are an EIA
standard for car stereo applications as follows:
YELLOW = BATTERY +12V Input
BLACK = GROUND Input
BLUE = REMOTE +12V Output
THE ABOVE POWER WIRES CAN BE CONNECTED DI-
RECTLY TO THE AMPLIFIER BEING ADDED
WHITE = LEFT Front (+) Input
WHITE/BLACK = LEFT Front (-) Input
GRAY = RIGHT Front (+) Input
GRAY/BLACK = RIGHT Front (-) Input
BLACK/WHITE = Reference Ground (-) (REFERENCE
GROUND OPTIONAL IF NOISE IS PRESENT)
NOTE: Be sure that all audio input connections are polarized or
in phase with each other. That is, the positive output wires from
the audio source need to be connected to the corresponding
positive input wires of the AX-ADCT2. The same goes for the
negative audio wires. Failure to do this will result in poor bass
response and low quality audio.
The AX-ADCT2 should be installed on a stereo’s speaker
output wires or the output wires on an OEM amplier of up to 80
watts per channel. These wires can be found behind the stereo
in the dash, on the outside of an OEM amplier, or on the input
terminals on the OEM speakers.
Wire Color & Function: The audio input wire colors are an EIA
standard for car stereo applications as follows:
YELLOW = BATTERY +12V Input
BLACK = GROUND Input
BLUE = REMOTE +12V Output
THE ABOVE POWER WIRES CAN BE CONNECTED DI-
RECTLY TO THE AMPLIFIER BEING ADDED
WHITE = LEFT Front (+) Input
WHITE/BLACK = LEFT Front (-) Input
GRAY = RIGHT Front (+) Input
GRAY/BLACK = RIGHT Front (-) Input
BLACK/WHITE = Reference Ground (-) (REFERENCE
GROUND OPTIONAL IF NOISE IS PRESENT)
NOTE: Be sure that all audio input connections are polarized or
in phase with each other. That is, the positive output wires from
the audio source need to be connected to the corresponding
positive input wires of the AX-ADCT2. The same goes for the
negative audio wires. Failure to do this will result in poor bass
response and low quality audio.
The AX-ADCT2 should be installed on a stereo’s speaker
output wires or the output wires on an OEM amplier of up to 80
watts per channel. These wires can be found behind the stereo
in the dash, on the outside of an OEM amplier, or on the input
terminals on the OEM speakers.
Wire Color & Function: The audio input wire colors are an EIA
standard for car stereo applications as follows:
YELLOW = BATTERY +12V Input
BLACK = GROUND Input
BLUE = REMOTE +12V Output
THE ABOVE POWER WIRES CAN BE CONNECTED DI-
RECTLY TO THE AMPLIFIER BEING ADDED
WHITE = LEFT Front (+) Input
WHITE/BLACK = LEFT Front (-) Input
GRAY = RIGHT Front (+) Input
GRAY/BLACK = RIGHT Front (-) Input
BLACK/WHITE = Reference Ground (-) (REFERENCE
GROUND OPTIONAL IF NOISE IS PRESENT)
NOTE: Be sure that all audio input connections are polarized or
in phase with each other. That is, the positive output wires from
the audio source need to be connected to the corresponding
positive input wires of the AX-ADCT2. The same goes for the
negative audio wires. Failure to do this will result in poor bass
response and low quality audio.

Axxess AX-ADCT2 Specifications

General

Brand	Axxess
Model	AX-ADCT2
Category	Media Converter
Language	English